7. At laundromats, using coins and/or pre-paid cards will turn on a dryer machine which consists of a heating source and a motor that turns the inner cylindrical chamber where the wet fabrics are placed. Once a certain amount of time has passed, the dryer will automatically turn off. a) Please create a combination logic gate using AND, NOT and/or OR logic gates that would simulate the logic gate circuit necessary to produce the same outcome as a timed dryer machine. Be sure to properly label and explain your logic gate system. b) Please create a combination logic gate using only NAND logic gates that would simulate the logic gate circuit necessary to produce the same outcome as a timed dryer machine. Be sure to properly label and explain your logic gate system.

7. At laundromats, using coins and/or pre-paid cards will turn on a dryer machine which consists of a heating source and a motor that turns the inner cylindrical chamber where the wet fabrics are placed. Once a certain amount of time has passed, the dryer will automatically turn off. a) Please create a combination logic gate using AND, NOT and/or OR logic gates that would simulate the logic gate circuit necessary to produce the same outcome as a timed dryer machine. Be sure to properly label and explain your logic gate system. b) Please create a combination logic gate using only NAND logic gates that would simulate the logic gate circuit necessary to produce the same outcome as a timed dryer machine. Be sure to properly label and explain your logic gate system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering 3. For the logic circuit in Figure 1, compute the following parameters: A) The total number of single stuck-at faults. B) The total number of all possible multiple stuck-at fault combinations. C) The total number of stuck-open faults. Note: You can assume that 3-input AND gate is realized using 8 transistors, a two-input OR gate is realized using 6 transistors, and an inverter is realized using 2 transistors.
Below is a logic diagram of a sequential circuit.b)Explain whether the circuit is a Mealy or Moore circuit.c)Analyze the behavior of the circuit.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
For the logic diagram shown in Figure 2, find logic function Q prove it is equivalent to Ex-NOR gate. i. A- DDO B
16) Answer each of the following with reference to the overfill alarm program shown in the figure below. a. Assume that the vessel is filling and has reached the 300-lb point. State the status of each of the logic rungs (true or false) at this point. b. Assume that the vessel is filling and has reached the 480-lb point. State the value of the number stored in each of the following words at this point: (1) I:012 (2) N7:1 c. Assume that the vessel is filled to a weight of 502 lb. State the status of each of the logic rungs (true or false) for this condition. d. Assume that the vessel is filled to a weight of 510 lb. State the value of the number stored in each of the following words for this condition: (1) I:012 (2) N7:1 18 e. With the vessel filled to a weight of 510 lb, state the status of each of the logic rungs (true or false). Inputs Ladder logic program Ouputs Fil Stop Start Full solenoid L2 Fill Fil solenoid solenoid Fill Filing solenoid Filing Full Ful GEQ GREATER THAN OR EQUAL…
6. The logic circuit: (From minimum SOP (Y2)) Number of gates used in the circuit: 2-Input AND gate.gates 2-Input OR gate, NOT gate. Number of idle gates in the chip: 2-Input AND gate 2-Input OR gate. NOT gate... 7. The logic circuit: (From minimum POS (Y3)) gates gates 2-Input AND gate 2-Input OR gate. NOT gate. gates gates gates Number of gates used in the circuit: 2-Input AND gate 2-Input OR gate NOT gate Number of idle gates in the chip: gates gates gates gates gates gates TC name: IC name: IC name: IC name: IC name:, IC name: ment
A logic program produces set of logic data as depicted in the Table 2 below. This logic program consumed around of 1MB of memory space if it was to be stored in a PLC. However, the PLC is only capable of storing around half of the required size. (a) What will you do to solve this problem? (b) By using solution suggestion in question (a), propose the new logic function (c) Determine the type and numbers of logic gates are required for the new logic function (d) Draw the logic gate
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
The logic circuit: (From minimum SOP) Number of gates used in the circuit: 2-Input AND gate.. 2-Input OR gate. NOT gate Number of idle gates in the chip: 2-Input AND gate 2-Input OR gate... NOT gute The logic circuit: (From minimum POS) gates gates gates gates gutes Number of gates used in the circuit: 2-Input AND gate 2-Input OR gate... NOT gate Number of idle gates in the chip: 2-Input AND gate... 2-Input OR gate, NOT gate, IC name: IC name: IC name: gates IC name: gates IC name: gates IC name: gates gates gates
1. Design a combination circuit and write a logic circuit when there are 3 switches and 1 lamp, the lamp will light when there are at least 2 switches per circuit.
Draw the logic circuit in the following figure?
Realize the following function ; " on the image " using a(a) 4-to-1 multiplexer, and draw the logic diagram.(b) 8-to-1 multiplexer, and draw the logic diagram.You may use external gates if needed.