8- Auto transformer is used in tuned amplifier to (transform low impedance of transistor input, match to the load, tune to operating frequency, stabilize tuned amplifier). 9- The dual slope A/D converter is popular because it is (fast converter, low power, low complexity, high resolution). 10- The most important feature of flash type A/D converter is (high resolution, fast, low component spread, low power dissipation).

8- Auto transformer is used in tuned amplifier to (transform low impedance of transistor input, match to the load, tune to operating frequency, stabilize tuned amplifier). 9- The dual slope A/D converter is popular because it is (fast converter, low power, low complexity, high resolution). 10- The most important feature of flash type A/D converter is (high resolution, fast, low component spread, low power dissipation).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

the way of working for boost dc-to-dc converter.
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230v (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di v: = VmSin ot Vs V. + Vy = VSin ot D2 Full-wave rectifier. Circuit operation during positive half cycle ell + ミ」
Draw the circuit diagram with shape of signal after transformer, after bridge rectifier, with capacitor and with voltage regulator.
In the full-wave rectifier circuit, the transformer has a turn ratio of 1:2. The transformer's primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50. For this circuit, determine the DC output voltage (3 significant figures)
In the full-wave rectifier circuit of figure , the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to-peak ripple in the output voltage
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
what is the difference of MOSFET and Diode in Boost Converter. Can you also sight an example?
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load resistance of 100 ohms. What are the average values of load voltage and current when firing delay angle is; 1. 140 degrees. 2. 30 degrees.
Create this using LTSpice B. Simulation showing each required output/waveform.a. Output of transformerb. Output of rectifierc. Output of filterd. Zener diode or load output
for the above boost converter, what is the max voltage stress on the MOSFET and diode? what is the output voltage peak to peak ripple?