A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a uniform distributed load of 800 N per meter. The beam has integrated into it a cylindrical tank, and the cross-section details for the beam-tank assembly are shown on the next page. The tank has an outer diameter of 166 mm and an inner diameter of 152 mm. The substance inside the tank has a gage pressure of 320 kPa. The pin in the pin-connection is located 60 mm up from the bottom of the beam. Determine the internal forces (V, N, & M) at the centroid of a section taken 8 m TO THE RIGHT OF THE LEFT END OF THE BEAM (4 m to the right of point A). 40 kN- A B 13 78 KN

A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a uniform distributed load of 800 N per meter. The beam has integrated into it a cylindrical tank, and the cross-section details for the beam-tank assembly are shown on the next page. The tank has an outer diameter of 166 mm and an inner diameter of 152 mm. The substance inside the tank has a gage pressure of 320 kPa. The pin in the pin-connection is located 60 mm up from the bottom of the beam. Determine the internal forces (V, N, & M) at the centroid of a section taken 8 m TO THE RIGHT OF THE LEFT END OF THE BEAM (4 m to the right of point A). 40 kN- A B 13 78 KN

Name: A 15-meter long beam-tank assembly supports the loading shown in addi
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is auniform distributed load of 800 N per meter. The beam has integrated into it a cylindrical tank, and thecross-section details for the beam-tank assemb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.100P: The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
Two hemispherical shells of inner diameter 1m are joined together with 12 equally spaced bolts. If the interior pressure is raised to 300kPa above atmospheric pressure, determine the tensile force in each bolt.
A factory's pressure tank rests on the upper base of a vertical pipe whose inside diameter is 1 ft. and whose length is 40 ft. The tank is a vertical cylinder surmounted by a cone, and it has a hemispherical base. If the alti-tudes of the cylinder and the cone are respectively 6 ft. and 3 ft. and if all three parts of the tank have an inside diameter of 6 ft., find the volume of water in the tank and pipe when full.
A storage tank contains oil and water as indicated in the figure. At the point where the two liquids exert the resultant force, on the ABC side of the tank, it has a width of 1.25 m, a load cell has been placed, making the point of application coincide with the resultant force. Consider the relative densities of oil 0.9, and water 1. The compression load cell consists of two active arm meters, mounted on a rectangular steel bar (12 mm x 12 m), with four isoelastic gauges, according to the pattern indicated in the figure (2 longitudinal and 2 transverse) and connected in a Wheatstone bridge to 12 V. Determine: А. The applied force and its position В. Voltage output C. Could the system be considered as a level measurement method? Explain your answer correctly. 0.75 m 1.5 m
The cylindrical steel tank shown is 3.5m in diameter 5m high and filled with brine solution. Brine has a density of 1198kg/m3. The thickness of the steel shell is 12.5mm. Calculate the tangential stress and the longitudinal stress in the tank, MPa
The cylindrical portion of the propane tank has an outer diameter of 12.02 in. and a wall thickness of 0.13 in. Calculate the longitudinal stress (in psi) in the wall of the cylinder when the tank is pressurized to 162.2 psi.
The 0.5-m-radius semi-circular gate is hinged through the top edge AB. Find the required force to be applied at the center of gravity to keep the gate closed.
The submerged sector gate AB shown in the figure is 1/9 of a circle of radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate. B Water radius 536.078 kN 113.001 kN 208.119 kN 162.328 kN 448.161 kN 262.874 kN 591.263 kN 89.207 kN 324.260 kN 490.984 kN 392.273 kN 127.908 kN
In the Fig. is shown the cross-section of the tank full of water under pressure. The length of the tank is 2.5 m. An empty cylinder lies along the length of the tank on one of its corners as shown. Find the horizontal and vertical components of the force acting on the curved surface LMN of the cylinder