A 50 V range voltmeter is connected across the terminals "A" and "B" of the circuit shown in figure below. Find the reading of the voltmeter under open circuit and loaded conditions. Also, find the accuracy and loading error of this instrument. What would be your recommendation to reduce this error? 200k2 A 100V 200k2 Voltmeter В

A 50 V range voltmeter is connected across the terminals "A" and "B" of the circuit shown in figure below. Find the reading of the voltmeter under open circuit and loaded conditions. Also, find the accuracy and loading error of this instrument. What would be your recommendation to reduce this error? 200k2 A 100V 200k2 Voltmeter В

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
The step currents of the three-stage Aytron (universal) shunt ammeter in the figure (I stage, II stage andCalculate the current values to be measured in III stage)
(b) Discuss the impact of connecting a large capacitor filter across the load in Figure Q1(ii). Use appropriate waveform sketch to aid your discussion. + Vp - Us R2 RL Vs ( (i) (ii) Figure Q1. Single phase half bridge rectifier: (i) with a Thyristor (ii) with a Diode
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 v and V2=8 V. R DZ D1 Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform Windows hui
In terms of polarity, the output of a full-wave rectifier has both alternations of the sine wave input voltage going in the direction. What is the main advantage of full-wave rectifier over the half-wave rectifier? The main advantage of the bridge rectifier over the standard full-wave rectifier is that it does not require a transformer. When one of the diodes in the bridge circuit opens, one of the will be missing at the output. From the data, what conclusion can you draw about the relationship between the dc voltage across R. and peak voltage in a full-wave rectifier?
Compute the V2(peak) Half of 2nd windings, Vout(peak), Vout(DC), fout in the center tapped rectifier circuit below: Note: The table shows the values measured using Multisim 10 application
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 V and V2=9 V. R DZ D1 Vin Vout v2 Maximum voltage of output waveform Minimum voltage of output waveform
Consider the Zener diode circuit shown in Figure. The Zener Breakdown Voltage (Vz) is 5.6 V at Iz= 0.1mA. Zener resistance is rz= 10 0. What is Vo without load (RL= ) ? R= 0.5 ko Vo R Vps= 10 V
Design a full wave rectifier based on the circuit shown in Figure 5 below: N1: N2 D3 D1 RL vs D2 DA Figure 5 The required specification for the full wave rectifier circuit includes the peak output voltage of 5 V, deliver 100 mA to the load R1, and produce an output with a ripple of not more than 5 percent. An input line voltage of 220 V (rms), 50 Hz is available. Given Vy = 0.7 V. (d) Calculate v, (max). (e) Find the required turn ratio for the transformer. (f) Determine the Peak Inverse Voltage (PIV). What is the effective load resistance? (h) Determine the required capacitance of the filter capacitor.