A 6 cylinder 4 stroke engine operating on a diesel cycle, the diesel cycle has initial conditions of 1 kg/cm^2 and 20 C. The compression ratio is 15 and the maximum temperature is 3300 K. The engine is operating at 1500 rpm on an AF = 16, resulting in an output torque of 150 N.m and has a bsfc = 0.856 kg/kWh (Calorific value of the fuel is 44000 kJ/kg). The surrounding air conditions are 1 bar and 20 C. Find A) The net output work of the cycle [kJ] B) The air standard cycle efficiency [%] [ C) The brake mean effective pressure for the engine [kPa] D) The volumetric efficiency of the engine [%] [ E) Relative efficiency based on indicated nower [%1

A 6 cylinder 4 stroke engine operating on a diesel cycle, the diesel cycle has initial conditions of 1 kg/cm^2 and 20 C. The compression ratio is 15 and the maximum temperature is 3300 K. The engine is operating at 1500 rpm on an AF = 16, resulting in an output torque of 150 N.m and has a bsfc = 0.856 kg/kWh (Calorific value of the fuel is 44000 kJ/kg). The surrounding air conditions are 1 bar and 20 C. Find A) The net output work of the cycle [kJ] B) The air standard cycle efficiency [%] [ C) The brake mean effective pressure for the engine [kPa] D) The volumetric efficiency of the engine [%] [ E) Relative efficiency based on indicated nower [%1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spark – ignition engine has a compression ratio of 8.5 and a maximum temperature of 945.15K. At the beginning of compression stroke, P and T of the fluid are 0.1 MPa and 28.65 deg C. Assuming hot air-standard analysis, how much work (kJ/lb) is produced per cycle completion?
Q3:A small truck has #cylinder ,4 liter compression ignition engine that operates on ir standard Dual cycle with air fuel ratio of 16:1, the compression ratio is 17 and the cylinder diameter is 14.5Cm. At the start of compression stroke Ta=50'C and Pa=100 kpa .It can be assumed the half of the heat input is added at constant volume and halt at constant pressure Calculate: 1-Temperature and pressure at each state of the cycle. 2-Indicated thermal efficiency. 4:28 PM
A four-cylinder spark-ignition engine with a compression ratio of 8 has a pistonswith a bore of 9 cm and a stroke of 10 cm. The air pressure at the beginning of thecompression is 98 kPa, and the temperature is 37 oC. The engine may be modeled by theair-standard Otto cycle. The maximum cycle temperature is 1700 oK. If the engineproduces 75 kW of power, determine a) the heat supplied per cylinder; b) the thermalefficiency; and c) the rpm required.
What is the highest temperature attainable of an otto cycle engine that have compression ratioof 15, the energy input from fuel is 500 kilojoules per kilogram and it operates at an ambient airtemperature of 25 degrees Celsius.
For an engine working on the ideal Dual cycle, the compression ratio is 10 and the maximum pressure is limited to 70 bar. If the supplied is 1680 kJ/kg, find tlerressures and temperatures at the vaae the cycle ane kJ yele efficiency. The pressure and temperature of air at the commencemelil Of compression are 1 bar and 100 °C respectively. Assume Cp = 1.004 kJ/kg K and Cy .e «alient points of 0.717 kJ/kg K for air.
An oil engine operating on a dual cycle the pressures in the cy linder at the end of the compression stroke and 60% of the compression stroke are 35bar and 4 bar respectively. Assume that the compression follows the law PV4= C. The ratio of maximum to minimum pressure is limited to 70 and fuel injection is end at 8% from the total stroke. Find the compression ratio of the engine and the thermal efficieney. [Cr=1.005 KJkg.k, Cv= 0.718 KJkg.k]
Home works Q₁) In an ideal otto cycle engine, the temperature and Pressure at the beginning of Compression are 43 °C 100 kpa respectively and the temperature at the end of adiabatic Compression is 323%. if the temperature at the end of Gnstant Volume heat addition is 1500°C Calculate: (a) the Compression ratio, (b) the air- standard efficiency, (c) the temperature and pressure at the end of adiabatic expansion. Assume Yas 1.4 for air.
A four cylinder 2.5liter SI automobile engine operate3s at WOT on a four-stroke air standard Otto cycle at 3000rpm. The engine has a compression ratio of 8.6:1, a mechanical efficiency of 86% and a stroke-to-bore ratio S/B = 1.025. Fuel is isooctane with AF=15, a heating valve of 44,300kJ/kg and a combustion efficiency ƞc=100%. At the start of the compression stroke, conditions of the cylinder combustion chamber are 100kPa and 60°C. It can be assumed that there is a 4% exhaust residual left over from the previous cycle. Calculate the: (a) Indicated mean effective pressure in kPa, (b) Indicated power in kW & Hp, (c) Piston speed at m/sec
A compression-ignition engine with compression ratio of 14 is being designed. Pressureand temperature at the bottom dead centre are 1.3 bar and 400K. The engine operatesaccording to the standard Diesel cycle. Assume polytrophic index to be 1.33. Computepressure and temperature at the top dead centre
The stroke and cylinder diameter of a compression ignition engine are 250 mmand 150 mm respectively. If the clearance volume is 0.0004 ?^3 and fuelinjection takes place at constant pressure for 5 per cent of the stroke determinethe efficiency of the engine. Assume the engine working on the diesel cycle.
It is desired to increase the compression ratio of spark ignition engine for 8 to 10. Assuming a ratio of constant pressure to constant volume specific heat to be 1.3, what will happen to the effeciency of the engine.?
Q3:A small truck has #cylinder ,4 liter compression ignition engine that operates on irstandard Dual cycle with air fuel ratio of 16:1, the compression ratio is 17 and the cylinderdiameter is 14.5Cm. At the start of compression stroke Ta=5O'C and Pa=100 kpa .It can beassumed the half of the heat input is added at constant volume and halt at constant pressureCalculate:-Temperature and pressure at each state of the cycle. -Indicated thermal efficiency.