A Beam is built up from the following plates. 450mm x 20mm as flanges and 500mm x 20mm as web. All plates are A36 steel with Fy=248 MPa and the flanges are continuously connected to web by means of fillet welds. The beam has a simple span of 4m. Laterally supported only at supports with total uniform load of 500 kN/m. Is the beam safe for bending

A Beam is built up from the following plates. 450mm x 20mm as flanges and 500mm x 20mm as web. All plates are A36 steel with Fy=248 MPa and the flanges are continuously connected to web by means of fillet welds. The beam has a simple span of 4m. Laterally supported only at supports with total uniform load of 500 kN/m. Is the beam safe for bending

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.4.1P

See similar textbooks

Similar questions

Part A - Identifying zero-force members Consider the truss shown below. Identify the zero-force members. A P_ E B D Check all that apply. • View Available Hint(s) ВС АВ ВЕ AE DE CD O CE Submit
Answers: AB = kN E AH = kN Determine the force in each member of the loaded truss. All triangles are 3-4-5. Enter a the member is in tension, negative if in compression. BC - kN C 34kN kN BG E 34 kN BH - kN 15 kN BI = kN D B kN kN A E DE kN H G F DF = kN - 4 panels at 8 m- DG = kN DI kN EF = kN FG - kN GH = kN
The following support is called: O a. Roller O b. Hinge O c. Fixed O d. Rocker
One plate of size 100 mm x 12 mm is lap joined to another plate of size 200 mm x 12 mm by fillet weld of size 10 mm. Lap length is 100 mm. Fillet weld is provided on all the three sides of the smaller plate. Determine the maximum axial tension the joint could carry. Assume the plates are of mild steel of grade 250 N/mm?.
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
1. Zero Force Members B T АЯ Identify the Zero Force Members in the Truss Structure below. C D E F G P INA MA O M L H 500lbf Q K
2: The truss is supported by a pin in point A and a roller at point E. Show your FBD 2 m F 5 kN. B 3 m A E 10 kN 5 m 5 m
ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to fasten the said members to the gusset plate? K.R.R.P. wwwwwwww 00 400 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B 75X75X6 mm ------------- · ET---- I 14 mm thick GUSSET PLATE P BC 75X75X13 mm P BE
Question 2: Determine the force in members DC, HI, and JI of the truss and state if the members are in tension or compression. Use method of sections. (Suggestion: Use the sections shown.) -3 m |- 2 m -|- 2 m--|-- -3 m G E 2 m 2 m 4 m 12 kN S t H D 16 kN t K C A 1-2 m-1-2 m- B
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
3) Determine the Force in each member of the truss shown in the Figure. (Use the Method of Joints.) D B gl 12' H E 300lb 300lb goolb 9' 9'
How many Zero force members are there in the truss shown? В D F E A K H[100 kN 60 kN LL 60 kN O 2 O 3 5 O 7