A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressive load the composite strut can support if the stress in the concrete is not exceed 2N/mm?. By how much should the strut shorten under this load. For cat iron EA= 100GN/m? and for concrete Eb = 10GN/m?. %3D

A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressive load the composite strut can support if the stress in the concrete is not exceed 2N/mm?. By how much should the strut shorten under this load. For cat iron EA= 100GN/m? and for concrete Eb = 10GN/m?. %3D

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
A reinforced concrete tied column is to resist the following axial load: • PDL= 800 kN • PLL = 1050 kN • PEL = 450 kN The concrete used has strength of 20.7 MPa and the yield strength of 415 MPa. Determine the number of 25-mm bars if the steel ratio is 1.5%.
An HSS9 x 7 x3⁄8 filled with concrete is used as a composite column, as shown in Figure. The steel has a yield stress of Fy = 46 ksi, and the concrete has a compressive strength of f ,c =4 ksi. Compute the nominal strength of the column.
A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressive load the composite strut can support if the stress in the concrete is not exceed 2N/mm². By how much should the strut shorten under this load. For cat iron EA= 100GN/m² and for concrete Eb = 10GN/m².
(1) (2) steel stress-strain Curve Es= Esteel = what is f db #3 #4 #5 #6 #7 #8 #9 #10 ksi 0.005 Ab FOR Grade 60 steel. E Ey = when fs = 45 ksi lbs/ft_ when Es=0.005
c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) – M1= 35kN.m and (ii) – 120kN.m Cross-section: width height Modulus of elasticity: concrete reinforcement Reinforcement: depth area b:= 300-mm h := 520-mm Ec:= 30-GPa Es:= 200-GPa d:= 460-mm As 1470-mm 2 h d b
9:YA I docs.google.com/forms O :D * Required Question 1 Determine the maximum stresses in the stepped shaft composite of two materials steel and Aluminum that fixed at the two ends as shown in Figure. It is subjected to a torque of 300 N.m at the section C. The larger section is of Aluminum and the smaller one is of steel. Gs = 82 GPa and Gal = 27 GPa. * 150 D St AI 50 300 N.m 600 500 1 Add file Page 2 of 3 Вack Next Never submit passwords through Google Forms.
A 6m-simply supported beam cross-section is show in the figure below is prestressed with 15 wires of 5mm diameter at the bottom and 3 wires at the top. Assuming prestress in steel is 840 MPa and the density of concrete is 24kN/cu.m. Calculate the stress at bottom extreme fiber at midspan. (MPa) 250 mm- 25 mm 350 mm 65 mm
A singly reinforced rectangular section has a width of 250mm and an effective depth of 460mm. The concrete has a compressive strength of 21MPa. The steel has a yield strength of 275 MPa and E = 200,000 MPa. Calculate the ideal flexural strength for the following areas of steel: a. 2580 mm² b. 5160 mm² c. The value at balanced failure
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi
Using the stress block, determine the ultimate moment of resistance of the section shown in Figure 2 and check whether the steei provided satisfies the bending moment due to the loads on the beam. Characteristic compressive strength of concrete, fck= 25 N/mm² Characteristic tensile strength of steel, fyk = 500 N/mm2 Clear cover to main steel as 20 mm. Ultimate Design Load =13 kN/m 2 402 mm 370 mm 2 1470 mm 9 m 230 mm Figure 2