A certain type of piping system uses deformable rings to clamp pipes onto fittings. A crimping tool that isused to make these connections is shown here. Find the internal forces and bending moment in the lowerjaw at section s-s, located midway between pins B and E, when a force of F = 63 lb is applied to thehandles as shown. Be sure to follow the sign conventions for internal loadings when entering your answers.2013 Michael SwanbomCCcrimpringBY NC SAabсdh₁h₂●statb-d-FValues for dimensions on the figure are given in the following table. Note the figure may not be to scale.Variable Value1.96 in7 in1.29 in14.3 in5 in9 inHINT: The assume the ring has no frictionThe internal axial load at section s-s in the lower jaw is A =The internal shear load at section s-s in the lower jaw is V =The internal bending moment at section s-s in the lower jaw is M =ولاIFlb.lb.in-lb.

Answered: Image /qna-images/answer/49c1fcd5-bacc-46ed-b09f-629df61c75e2.jpg

A certain type of piping system uses deformable rings to clamp pipes onto fittings. A crimping tool that is used to make these connections is shown here. Find the internal forces and bending moment in the lower jaw at section s-s, located midway between pins B and E, when a force of F= 63 lb is applied to the handles as shown. Be sure to follow the sign conventions for internal loadings when entering your answers. 2013 Michael Swanbom C180 BY NC SA crimp ring IF Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a b с d h₁ h₂ a ●E 1.96 in 7 in 1.29 in 14.3 in 5 in 9 in b→ -d. с HINT: The assume the ring has no friction The internal axial load at section s-s in the lower jaw is A - The internal shear load at section s-s in the lower jaw is V- The internal bending moment at section s-s in the lower jaw is M - lb. lb. in-lb.

A certain type of piping system uses deformable rings to clamp pipes onto fittings. A crimping tool that is used to make these connections is shown here. Find the internal forces and bending moment in the lower jaw at section s-s, located midway between pins B and E, when a force of F= 63 lb is applied to the handles as shown. Be sure to follow the sign conventions for internal loadings when entering your answers. 2013 Michael Swanbom C180 BY NC SA crimp ring IF Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a b с d h₁ h₂ a ●E 1.96 in 7 in 1.29 in 14.3 in 5 in 9 in b→ -d. с HINT: The assume the ring has no friction The internal axial load at section s-s in the lower jaw is A - The internal shear load at section s-s in the lower jaw is V- The internal bending moment at section s-s in the lower jaw is M - lb. lb. in-lb.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the shear force and bending moment diagrams for each of the diagram.
RN1 = 7921 round off maximum tension to the nearest whole number
a b c d h 82 mm 139 mm 39 mm 18 mm 33 mm Clamps like the one shown are commonly used in woodworking applications. This clamp has the dimensions given above, and its jaws are 38 mm wide (in the direction perpendicular to the plane of the picture). The screws of the clamp are adjusted so that there is a uniform pressure of 190 kPa being applied to the workpieces by the jaws. Find the force carried in each screw.Note: Assume that A, B, C, and D act as pins. (Denote tension forces with positive values; compressive forces with negative values.)
QUESTION 2: For the nose landing gear of an aircraft shown in the figure, calculate the internal forces at the vertical section at point A. -150 mm 20 mm- 60° 300 mm -175 mm 12 kN
Assignment 2 A Copper bar is loaded as shown complete the following: a. Draw a neat shear force and bending moment (Table of values is required) b. Calculate the maximum bending stress, clearly indicate where this occurs c. Calculate the maximum shear stress, clearly indicate where this occurs d. Plot the bending and shear stress for the cross section at x= 4 ft. from the left hand support. Clearly show the calculations were made at the following positions: y-0, 2, 4, 6, 8, 10 and 12 35 Ib/ft. 200 Ib Beam cross section 12 65" 8 ft. 5ft. 3 ft.
Figure 2: Given the below determine the bar force at AB. (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 2) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
X Z d₁ B
Question 5 Calculate the maximum longitudinal direct stress, plot the stress distribution diagram and determine the location of the neutral axis for a 20 long simply supported beam with a rectangularcross-section that is 160 mm wide and 210 mm deep, which carries a uniformly distributed load of 260 N/m, on its upper surface and a compressive axial load of 220 kN at its free ends. Present schematics showing the distribution of bending direct longitudinal stress, direct load stress, the combined longitudinal direct stress, and identify the neutral axis as well as centroidal axis on the schematic. Show the values of these stresses at the top and bottom surfaces of the cross-section.
Draw bending moment diagram for the loading shown in Figure Q15
Figure 4: Determine the bar force at FN (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 4) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
The connected pipes are attached to the wall with a fixed support; i.e. built in. Calculate the reaction forces due to the loading shown. FBD required, can be more sketch like, but must have all reactions drawn and labeled.The 150 N force is parallel to the z axis; −150 k', the 200 N force is parallel to the y axis; 200 j,̂I will assume that all of the moment support reactions(curved arrows) are drawn positive.
The shelf bracket is subjected to the force F = 336 Newtons at an angle 0 = 25.5°. Compute the moment (in N-m) that this force exerts about each of the two attachment points (screw locations in the figure). Take counterclockwise moments to be positive. a F 2013 cc CC Michael Swanbom BY NC SA Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 48.0 cm 45.6 cm 4.10 cm The moment about the upper attachment point is N-m. The moment about the lower attachment point is N-m. luk-