A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 60 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 90 MPa. If a torque of TC = 23,000 N-m is applied at C, determine the minimum required diameter of (a) the brass shaft and (b) the aluminum shaft.

A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 60 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 90 MPa. If a torque of TC = 23,000 N-m is applied at C, determine the minimum required diameter of (a) the brass shaft and (b) the aluminum shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 Ib-A 50 Ib-ft 70 Ib-ft (1) (2) 30 Ib-f (3) 827 psi O 880 psi O 956 psi 691 psi O 739 psi
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 31 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 60 MPa. If a torque of Tc-8,500 N-m is applied at C, determine the minimum required diameter of the brass shaft (1). Tcl O 144.1 mm O 69.1 mm O 1118 mm O 89.9 mm O 1224 mm
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 320 N-m, Tc = 371 N-m, and TD = 181 N-m. TD (3) O -208 N-m O -224 N-m O -138 N-m O -190 N-m O -265 N-m Tc (2) B TB (1) TA
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 59 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 84 MPa. If a torque of Tc=29400 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = d₂ = i (2) B A mm mm
L1=1.8 L2=.9 d1370 d2=53 Compound shaft ACB is fixed at A and consisting of two solid circular sections AC & CB, as shown, and is subjected to the given distributed torque. The diameter of part AC is DI, and the diameter of part CB is D2. The material of the shaft having a shear modulus of 69 GPa. Determine (a) the maximum shear stress (KPa) developed in shaft AB, (b) the angle of twist of point B. The values of LI, L2, D1, and D2 are given in table below for each student. DI 50 Nm/m C 0.2 m LI L2
A solid 0.72-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 2273 psi 1549 psi 1637 psi 1367 psi O 2118 psi 50 lb-ft B (2) 70 lb-ft (3) 30 lb-ft D
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment. Answers: T1 = i T2 = i (1) (2) MPa. MPa.
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 50 lb-ft 70 Ib-ft | (1) 30 lb-ft A (3) B D 3150 psi O 2524 psi 1876 psi O 2331 psi O 2932 psi