A conical friction clutch is used to transmit 70 kW at 1000 rpm. The semicone angle is 20° and the coefficient of friction is 0.2. If the outer diameter is 400 mm and the inner diameter is 340 mm and the intensity of normal pressure is not to exceed 0.20 N/mm². Determine the axial Force (F) required in Newton (N)

A conical friction clutch is used to transmit 70 kW at 1000 rpm. The semicone angle is 20° and the coefficient of friction is 0.2. If the outer diameter is 400 mm and the inner diameter is 340 mm and the intensity of normal pressure is not to exceed 0.20 N/mm². Determine the axial Force (F) required in Newton (N)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone clutch to increase torque. The cone clutch has an outer diameter of 500 mm and inner diameter of 300 mm. the cone has a face angle of 12.5° and a width of 45 mm. The coefficient of friction of 0.25 and normal pressure on the clutch face is not to exceed 0.1 N/mm? 3.1. Sketch the cone clutch and indicate all dimensions and forces. 3.2. Calculate the axial thrust. 3.3. Calculate axial spring force to engage. 3.4. Derteimine the wear. 3.5. Find torque.
A block chutch has four wooden shoes each contacting with 80 degrees of the inside of a 13-in drum The coefficient of fiction is 0.40 and the maximum contact pressure is not to exceed 40 psi This chitch is to transmit 20 hp at 280 rpm Determine the required width of the shoes. (Ans, 1.295 in)
2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
1. A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are alternatively of steel and phosphor bronze and they run in oil. The coefficient of friction is 0.08. The internal radius of the friction surface is 0.8 times the radius of the external surface. The axial pressure is limited to 20 x 104 N/m2 . If the maximum diameter of the frictional surface is not to exceed 250 mm, determine the number of plates required.
Q3/ A multi plate clutches an included angle of 120°. A multi plate clutch, has 2 discs on the driving shaft and1 on the drive shaft, the outer radius is 100 cm and inside diameters 600 mm. The maximum intensity of pressure at any point is 0.2 N mm. If the u is 0.25, determine the speed of the clutch if the power generated = 31582.807 kW. Use both the uniform wear theory and the uniform pressure theory %3D
A single disc clutch with both sides effective is required for a vehicle. The power for initial estimation of the clutch is 100 kW at 4000 rpm. Determine the radial dimensions (inner and outer radius) and the actuating force (W). Base the design on the uniform wear assumption. Assume maximum pressure (pmax) as 1.6 MN/m2 and ?2?1= 1√2where ‘r2’ and ‘r1’ represent inner and outer radius of the friction surface. Take µ = 0.35. Find also the minimum pressure (pmin).
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
The block brake, as shown in the figure, provides a braking torque of 376 N-m. The diameter of the brake drum is 258 mm. The coefficient of friction is 0.3. Find: a. The force (P), in Newtons, to be applied at the end of the lever for the clockwise rotation of the brake drum b. The force (P), in Newtons, to be applied at the end of the lever for the counter clockwise rotation of the brake drum; and c. The location of the pivot or fulcrum, in mm, to make the brake self-locking for the clockwise rotation of the brake drum.
A car engine has its rated output of 120 kW. The maxdmum torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axia! pressure is not to exceed 0.85 bar. External diamater of friction plate is 1.25 times the internal diameter. Determine the dimensions of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be 0.3.