A current of 3.4 A passes a 70 mH inductor. How much energy is stored in the inductor in W? Answer:
Q: explain project scope management process completely and their techniques.
A: Find the answer below. The complete amount of work required to achieve a good, service, or outcome…
Q: and classify as low /high pass filter
A: Given: Sketch ao an RL circuit and differential equation for that circuit. Also write Trnsfer…
Q: The circuit shown below on the left has the following parameters: Vs = 11 V Is=7A R₁ = 1.20 R₂=2.20…
A:
Q: Q₁-- a) The discrete time signal x[n] is defined by Find y[n] = x [2n + 3] Q₂-- x[n] = 1, -1, Sketch…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: What are the main limiting factors to battery improvements? Why is the infrastructure for battery…
A: Introduction: The main limiting factors to battery improvements. the infrastructure for battery…
Q: 1. Provide a block diagram and a function table for the NOR-Gate Latch. 2. Describe, with the aid of…
A: Since you have asked multiple questions, we will solve the first question for you If you want any…
Q: STA H⋅W. 1- Write the mesh equations, the find the current through R3 for the network R₁33-2 E₁ 15V…
A:
Q: The voltage across 20 Resistor where v= 10volts is 20 W O a. 4V O b. 10V О с. 3V O d. 2V in W m 20 V
A:
Q: For Z₁ = 1 KQ, Z₂ = 0.1 µF, Z3 = 500 №2, Z4 = 1 ko, derive an expression for the transfer function…
A:
Q: An angle-modulated signal has the form: Determine: (i) (ii) (iii) u(t) = 100 cos (27107t + 4 sin…
A:
Q: give a description of this wave form, from a non-synchronous buck converter. The wave form is from…
A: The signal waveform across the MOSFET is given as
Q: Calculate the dissipation in power across 2002 resistor for the FM signal v(t)= 20 cos(6600t+…
A: The expression of the FM signal is vt=20cos6600t+10sin2100t. The power dissipated via a 20-ohm…
Q: The gain margin of a system with loop function GH = 2 s(s+2) is:
A: Given, Loop function, GH=2ss+2
Q: Determine current in 5ohm resistor by any one method. 10 V + A 8 V www 202 + 12 V B i, 20 2 202 592…
A: Matrix-method for Mesh analysis can be used. Mark three loops as shown, in Fig. Resistance-matrix…
Q: the attached
A: Given: a) Write down the equation of 1st order Transfer Function in standerd form and the unit step…
Q: Consider the following transfer function. You may use codes to support your answers for the…
A:
Q: 2. For the voltage feedback network of Fig., determine: a) lc b) Vc c) VE d) VCE
A: It is given that:
Q: Consider the circuit of figure below. The op- amp used is ideal. Determine I, and Vop if V₁ = 2 [V].…
A:
Q: 15 A current? What is the radiation resistance of an antenna which radiates 5 kW when it draw
A: Given information: The current drawn by an antenna is I=15 A. The power radiated by the antenna is…
Q: Design a suitable 8 section starter for a 14.92 kW, 250 volt, 1000 rpm d.c. shunt motor from the…
A:
Q: ii) Just show induced current directions on figure 5 by using Lenz's law. Current I is constant and…
A: Note: We are authorized to answer one question at a time, since you have not mentioned which…
Q: The conductors of a three phase transmission line are symmetrically arranged in a triangle. If the…
A:
Q: Q.) The circuit shown below is an idealized forward converter. Assuming an input voltage Vd=40V,…
A: The forward converter, a DC/DC converter, raises or lowers the output voltage and offers galvanic…
Q: A piezo electric crystal having dimensions of 5 mm x 5 mm x 1.5 mm and voltage sensitivity of 0.055…
A: Given Data, Area of Crystal from dimensions = 5 mm * 5 mm Area (A) = 25 mm2 Voltage Developed (E0) =…
Q: What is the frequency for a wavelength of 2 meters? Show detailed calculation.
A:
Q: a) Find the spectrum of x(t) = e²t u(1-t) b) Find the inverse Fourier transform of X (w) = j
A:
Q: An npn transistor
A:
Q: 6. For the follow logic circuit system, the output f is: [ (A) ab. (B) a + b. (C) a'+b'. (D) a'b' a…
A: Given, The logic circuit is,
Q: (a) Calculate the synchronous speed of an eight-pole induction motor when supplied with power from a…
A: Given: An induction motor has following specifications, Number of poles, P=8 Frequency of source,…
Q: 6) Carson's rule is used to calculate a. Bandwidth of FM signal b. Signal to noise ratio c.…
A: The correct option along with the explanation has been provided in the following section.
Q: Explain Hall effect transducer also state Different values of hall coefficient with different…
A: The Hall effect transducers are based on Hall effect which was discovered in 1879. The Hall effect…
Q: Consider the normal AM signal s(t) = 4.4cos(2л1500t) + [0.21cos(2л100 Find Normal AM transmission…
A: Given an AM signal, st=4.4 cos2π1500t+0.21 cos2π1000t
Q: 2. Relation between currents according to KCL is 12 i1 i5
A: .
Q: Three capacitors 10 μµF, 20 µF, 30 uF are connected in series across 150V (sinusoidal). Then…
A: Given, Three capacitors are connected in series, C1=10 μFC2=20 μFC3=30 μF Supply voltage, Vs=150 V
Q: Que 1.18. L Determine the current I, as shown in Fig. 1.18.1(a). Assume that the diodes are ideal IL…
A: Solution !!
Q: A load of 500 kVA operates on 1100 V, 50 Hz mains with power factor of 0.6 lagging. It is required…
A: We have an load with, KVA rating = 500 KVA Vs = 1100 V Frequency (f) = 50 Hz Power factor (cosϕ1) =…
Q: Explain what is mean by "Programming device" in PLC, for what purpose it is used.
A: we have to define and explain use of "Programming device" in PLC.
Q: In a 100 volt circuit with a resistance of 25 ohms, the current flowing through the circuit is which…
A: Given data, Voltage V = 100 V Resistance R=25 Ω
Q: SS 2-45 Find to in the circuit of Figure P2-45- Μ 33 ΚΩ FIGURE P2-45 10 V Μ 100 ΚΩ 33%
A: Given circuit,
Q: 11- A conductor with a positive Q (charge) of 4 C has a 2.56 X 10^18 electrons added to it. It will…
A: Given data, Total charge Q =4 C Number of electron n=2.56×1018
Q: 9.10 Find the steady-state expression for vo(t) in the circuit shown by using the technique of…
A: For the given circuit calculation of steady state expression for v0(t) using source transformation:…
Q: Vin R₁ C₂ R3 C₁ HH 5-2 R₂ - Vout
A: The given band-pass filter is the narrow band-pass filter. In this filter, only one op-amp is used…
Q: Two circuits A and B are connected in parallel with a supply of 200 V, 50 Hz. In circuit A, an…
A:
Q: Three resisters are used in a circuit, with resistances R1 = R, R2 = 2R, and R3= 3R, where R = 7.5…
A: Given: R=7.5Ω and R1=R, R2=2R, R3=3R
Q: Calculate the radiation resistance of current element whose overall length is λ/50.
A:
Q: Show Work Please (Q8)
A: Given that: An infinite long wire carrying a uniform current I. Prove that: B→=μoI2πrθ∧
Q: VL 0 10V -15V t
A:
Q: Q8) If the initial conditions on y(t) and u(t) their derivatives are zero, find the transfer…
A: Note: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…
Q: Find the energy stored in the capacitor: 20 20V (a) + Vc T
A: Given data, Given circuit diagram is,
Q: A current of 3 A flows for 5 minutes. What charge is transferred?
A:
Step by step
Solved in 2 steps
- Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?4. In what form is the energy of a capacitor stored?
- You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?What frequency must be applied to a 33-mH inductor to produce an inductive reactance of 99.526 ?You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
- You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.The value of the Inductance can be determined by (W - is energy stored in inductor, I - current) O a. ½ W21 O b. 2W/ 12 O c. 2WI2 O d. 2W21
- What is the value of the induced voltage of the self-inductance when the rate of current is from 200 uA to 20 uA and the total time interval is 5 uS?The current through a 20mH inductance changes from 30 mA to 75mA in 12µs. How much is the value of self-induced voltage?A 10mH inductor was supplied by a 6e-t/2A current. What will be its voltage after 2 seconds of being charged?