Exercise 2-5:(a) Design an operational-amplifier circuit that will produce an output equal to-(4v₁₂+0.1v3). Use R= 60 k2.(b) Write an expression for the output and sketch its waveform when v₁ = 2 sin wt V,v2 +5 V dc, and v3 -100 V dc.=[Answers: (a) R₁ = 15 ks2, R2 = 60 ks2, R3 = 600 k2, R = 9.8 k2, Fig. 2-16(a)(b) v₁ = 5-8 sin wt, Fig. 2-16(b)]1015kQww60 k20w600 kQO9.8 kY-5-8 sin ut+13 V-3 V60 kw(a)(b)Fig. 2-16-(4₁₂+0.13)

Answered: Image /qna-images/answer/6132aefd-575d-4d45-a335-cd70aa1e6ed4.jpg

(a) Design an operational-amplifier circuit that will produce an output equal to -(4v₁₂+0.1v3). Use R-60 ks2. (b) Write an expression for the output and sketch its waveform when v₁ = 2 sin wt V, v2 +5 V de, and v=-100 V dc. [Answers: (a) R₁ = 15 ks2, R2 = 60 ks2, R3 = 600 k2, R. = 9.8 ks2, Fig. 2-16(a) (b) vo=5-8 sin wt, Fig. 2-16(b)] 15 kD w 6010 w IO 60k12 20 ww 600kQ O 9.8 เ -5-8 sin ur (a) +13 V A (b) Fig. 2-16 -(4x+x+0.1%)

(a) Design an operational-amplifier circuit that will produce an output equal to -(4v₁₂+0.1v3). Use R-60 ks2. (b) Write an expression for the output and sketch its waveform when v₁ = 2 sin wt V, v2 +5 V de, and v=-100 V dc. [Answers: (a) R₁ = 15 ks2, R2 = 60 ks2, R3 = 600 k2, R. = 9.8 ks2, Fig. 2-16(a) (b) vo=5-8 sin wt, Fig. 2-16(b)] 15 kD w 6010 w IO 60k12 20 ww 600kQ O 9.8 เ -5-8 sin ur (a) +13 V A (b) Fig. 2-16 -(4x+x+0.1%)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(i) For the circuit below, draw the output waveforms for both the given input wave- forms. (ii) How can you convert this circuit into a half-bridge by removing any two compo- nents? Please draw a circuit diagram. Also, draw the current flow through the modified circuit. This can be done by annotating the modified circuit diagram. M (i) (ii)
R2 741 DI R1 D2 In the circuit on the side, the input signal with a peak value of 4 V is applied case; Plot the graphs V0 (t) and V0 - Vi explaining. specify required values)
A silicon photodiode is connected to an op-amp as indicated. Under an illuminance of 500 lux, the photocurrent Ip is 80 nA. I R = 1MQ w out Write down the values of 11, 12 and Ip. From these values, deduce the output voltage. Briefly describe how this circuit works. c) Will this circuit work under sunlight? The illuminance of sunlight is about 100,000 lux. You may assume the photocurrent respond linearly with incident light flux, and the op-amp is powered between 9V alkaline cell. (i.e., V+ = 9V, V¯ at ground).
circuit in the figure.) VB=25.2 V, VD_ON=800 mV, R₁=5 k /Circuit Parameters Vin Vin is increased from - infinity to + infinity. For which condition of Vin, does D₁ starts to conduct?) What is the output voltage, Vout, if Vin=2.7 V?) A670, 196px VB D₁ WHET a. Vin-26.0 V Od. Vout=26.0 V Oe. Vin>24.4 V Of. Vout=-21.7 V Og. Vout=28.7 V O + R₁ Vout (Use the constant voltage model for the diode in the 1065 x 795px BBoyut: 67.0KB In this circuit,
For the circuit below with input voltage V1 shown and the initial voltage across Cl equal zero, find the transient response voltage across the resistor R1 and plot the results: (Provide your calculations and reasoning for your answer.) C1 5u V1- 15 V2 -5 TD = 0.010 TR = 0.00001 TF = 0.00001 PW.1 PER = V1 R1 1k Input Voltage V1 20 15 10 -0.02 -0.01 0.01 0.02 0.03 0.04 0.05 0.06 Time (sec) (A) TA
I want the answer with details as soon as possible. Please Q-Design an op-amp circuit to amplify the AC voltage of 0.7v to become 3v , And the voltage of VCC is 5v DC.
3. A generic op-amp circuit is shown in Figure 3. With the given data, answer the following by showing the corresponding circuit and by explaining your answer or presenting the solution. a. If VA-0, VB-1V, RA-RB-10kQ, R1=70kQ, R2=00 and vout-8V, which terminal (A or B) is the noninverting input? b. If VA-10, VB=0V and B is the inverting input, select RA, RB, R1, and R2 and to obtain an output voltage of 20V. c. If VA=VB=1V, R1=0, R2=∞ and Vout=1V, which terminal (A or B) is the inverting input? R2 VA RA OVout RB B VB R1
Q1: (a) Determine the rate of change of the output voltage in response to the input square wave, as shown in Figure (1). The output voltage is initially zero. The change in time is 100 us. (b)Describe the output and draw the waveform. (c) Design the circuit that produced the input, where Vin of that circuit is 5 V. 1.5 nF +3.2 V R; Vin -3.2 V 33.333 kN out Figure 1
(a) Design and implement the give expression from given de voltage Vdc-10v using op-amp.R2=100ohm and R1-120ohm (b) Find out the output voltage form the given expression? Vout = { [1+2*1*13.35*Vde+2.26*Vdc] } R1
Q1: (a) Determine the rate of change of the output voltage in response to the input square wave, as shown in Figure (1). The output voltage is initially zero. The change in time is 100 us. (b)Describe the output and draw the waveform. (e) Design the circuit that produced the input, where Vin of that circuit is 5 V. 1.5 nF +3.2 V in -3. 2 V 33.333 kn -이 out Figure 1
In a summing inverting amplifier,Rf is 100k ohms, V1 is a sinusoid with 2V amplitude and frequency of 1Hz ,R1 is 10k ohms, V2 is a sinusoid with 3V amplitude and frequency of 1Hz, and R2 is 10k ohms. Vs+ = 18 V and Vs- = ground. What is the output voltage? Please draw the waveform as well.
A generic op-amp circuit is shown in Figure 3. With the given data, answer the following by showing the corresponding circuit and by explaining your answer or presenting the solution. a. If VA=0, VB=1V, RA=RB=10kN, Ri=70KSN, R2=∞ and vout=8V, which terminal (A or B) is the noninverting inpuť? b. If VA=10, VB=0V and B is the inverting input, select RA, RB, R1, and R2 and to obtain an output voltage of 20V. c. If VA=VB=1V, R1=0, R2=0 and vout=1V, which terminal (A or B) is the inverting inpuť? R2 VA RA O Vout RB -B VB R1