a) Determine the maximum applied torque T without exceeding a maximum shearing stress of 50MPa for circular shaft, and 60MPA for the rivets Gahaft= 83GPa b) Determine the minimum thickness "t" of the tubular pipe with a maximum shearing stress of 70MPA c) Assuming point B is fixed, and the shaft A-B is 300mm long, determine the angle of twist developed at A relative to B

a) Determine the maximum applied torque T without exceeding a maximum shearing stress of 50MPa for circular shaft, and 60MPA for the rivets Gahaft= 83GPa b) Determine the minimum thickness "t" of the tubular pipe with a maximum shearing stress of 70MPA c) Assuming point B is fixed, and the shaft A-B is 300mm long, determine the angle of twist developed at A relative to B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Situation 2| A flanged bolt coupling, consists of 20mmø rivets arranged, is used to transfer the Torque "T" from a solid shaft 80mm in diameter to a 180mm square hollow tubular pipe with unknown thickness "t". 3) Determine the maximum applied torque T without exceeding a maximum shearing stress of 50MPA for circular shaft, and 60MPA for the rivets. Gshan=83 GPa. 4) Determine the minimum thickness “t" of the tubular pipe with a maximum 5) Assuming point B is fixed, and the shaft A-B is 300mm long, determine the angle of twist developed at A relative to B. shearing stress of 70 MPa. B 180 R10 R125. R80 08
A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
A muff coupling connects two shafts to transmit a torque of 135.6 N-m, the diameter of the shaft is 25 mm. If the shaft and the key are produce out of same material, the value of allowable shear strength of the shaft material is . N/mm? O 442.06 44.21 O 30.65 O 4.42 A process vessel shaft is coupled to the differential box shaft of diameter 30mm. If the allowable shear stress of the shaft material and the coupling is 57 MPa. The value of Maximum torque that it can transmit in N-mm is, a. 296328.75 O b. 302028.75 O c. 307728.75 O d. 1208115.00
The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The shaft is to be designed to safely transmit 200 hp at 3500 rev/ min. Determine the diameter of the smallest shaft that can be used and its corresponding angle of twist. For the steel, use a working shear stress of 12 000 psi and G = 12 x 106 psifind, a) diameter b) angle of twist
Find the max shear stress in given data of two circular shafts (S) AND (H)
2) A hollow tube constructed of metal is subjected to five torques acting in the directions shown in the figure. The tube has an outside diameter of 1.0 in. The allowable shear stress is 12,000 psi. The shear modulus is 9500 ksi. The length between AB, BC, CD and DE is 2ft. a) Draw the internal torque diagram for the shaft using the rules we discussed in class. Based on the allowable shear stress, design the inner diameter of the shaft in inches. b) c) Using your answer from part (b), calculate the total rotation between points A and C in radians. Be sure to track which direction each portion of the shaft is rotating. T₁= TB = T, = Tc= 1000 lb-in. 500 lb-in. 800 lb-in. 500 lb-in. A B D d₂ = 1.0 in. T₂= 800 lb-in. E
Z PUIm The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and is loaded by two torques. Use Gpronze = 35 GPa, Galum = 28 GPa, and Gsteel = 83 GPa. Bronze Aluminum Steel diameter = 25 mm diameter = 50 mm diameter = 25 mm T-300 N.m To-700 N.m K A 2 m 2 m 2.5 m Determine the maximum shearing stress developed in steel. Select the correct response 214.16 MPa 111.79 MPa 1.75 MPa 57.12 MPa
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
If the internal torque experienced by a hollow brass shaft (G = 39 GPa) at a section with diameter d = 100 mm with 3 mm thick walls is T = 12 kNm, which of the following is closest to %3D the magnitude of the minimum shear stress developed on that section? Select one: O A. 262 MPa O B. 501 MPa O C. 279 MPa O D. 533 MPa
A steel shaft can be manufactured as a circular rod with a solid body or a circular tube. The shaft is required to bear a torque of 1200 N.m. Since the shear strength for the shaft material is 40 MPa, the maximum permitted unit torsion angle of the bar is 0.750 / m and the shear modulus of the steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outer diameter d2 for a ring section shaft whose thickness is 1/10 of the outer diameter.c) Find the diameter ratio (d2 / d0) and the weight ratio for ring cross section and solid section shafts.
Q/A shaft supported at the ends in ball bearings carries a straight tooth spur gear at its mid span and is to transmit 7.5 kW at 300 r.p.m. The pitch circle diameter of the gear is 150 mm. The distances between the centre line of bearings and gear are 100 mm each. If the shaft is made of steel and the allowable shear stress is 45 MPa, determine the diameter of the shaft. Show in a sketch how the gear will be mounted on the shaft; also indicate the ends where the bearings will be mounted? The pressure angle of the gear may be taken as 20°.
A motor supplies 154 hp at 470 rpm to flange A of the shaft. Gear B transfers 74 hp of power to operating machinery in the factory, and the remaining power in the shaft is transferred by gear D. Shafts (1) and (2) are solid aluminum (G = 4400 ksi] shafts that have the same diameter and an allowable shear stress of r= 5.3 ksi. Shaft (3) is a solid steel (G-10800 ksi] shaft with an allowable shear stress of r = 12.3 ksi. Assume that Ly-2 ft. L₂-1.4 ft. Lg-1.8 ft. Determine: (a) the minimum permissible diameter dyd₂ for aluminum shafts (1) and (2). (b) the minimum permissible diameter da for steel shaft (3). (c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b). Answers: (a) d-da- (b) dj- (c) DIA= eTextbook and Media. 8 in. in. To