A flaked cereal is of thickness 2L = 1.2 mm. The density, specific heat, and thermal conductivity of the flake are p = 700 kg/m², c, respectively. The product is to be baked by increasing its temperature from T; = 20°C to T, = 220°C in a convec- tion oven, through which the product is carried on a con- veyor. If the oven is L, = 3 m long and the convection heat transfer coefficient at the product surface and oven air temperature are h = 55 W/m2 · K and T = 300°C, respectively, determine the required conveyor velocity, V. An engineer suggests that if the flake thickness is reduced to 2L = 1.0 mm the conveyor velocity can be increased, resulting in higher productivity. Determine the required conveyor velocity for the thinner flake. = = 0.34 W/m K, 2400 J/kg K, and k %3D %3D

A flaked cereal is of thickness 2L = 1.2 mm. The density, specific heat, and thermal conductivity of the flake are p = 700 kg/m², c, respectively. The product is to be baked by increasing its temperature from T; = 20°C to T, = 220°C in a convec- tion oven, through which the product is carried on a con- veyor. If the oven is L, = 3 m long and the convection heat transfer coefficient at the product surface and oven air temperature are h = 55 W/m2 · K and T = 300°C, respectively, determine the required conveyor velocity, V. An engineer suggests that if the flake thickness is reduced to 2L = 1.0 mm the conveyor velocity can be increased, resulting in higher productivity. Determine the required conveyor velocity for the thinner flake. = = 0.34 W/m K, 2400 J/kg K, and k %3D %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermal properties of mould and Iron is given as latent heat of iron = 270 the freezing temperature of iron = 1500 C. the density of molten iron = 7500 kg kJ kg-K the specific heat of mould material = 1.2 the themal condudivity of mould material = 09 Wm-K the density of the mould material = 1500 kg Determine the solidification time for a slab-shaped casting of 16 e thickness when iỘn withaut superheat is poured into the sand mold at an initial m temperature of 300 C BI U
2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number? 2-G: For flow over a flat plate, sketch variation of local convective heat transfer coefficient, h(x), versus the distance along the plate x for laminar, transition, and turbulent flow regimes.
5.10 A flaked cereal is of thickness 2L = 1.2 mm. The density, specific heat, and thermal conductivity of the flake are p = 700 kg/m³, cp = 2400 J/kg K, and k = 0.34 W/mK, respectively. The product is to be baked by increasing its temperature from T₁ = 20°C to T, = 220°C in a convec- tion oven, through which the product is carried on a con- veyor. If the oven is L₁ = 3 m long and the convection heat transfer coefficient at the product surface and oven air temperature are h = 55 W/m² K and T. = 300°C, respectively, determine the required conveyor velocity, V. An engineer suggests that if the flake thickness is reduced to 2L = 1.0 mm the conveyor velocity can be increased, resulting in higher productivity. Determine the required conveyor velocity for the thinner flake. 2L = 1.2 mm Conveyor belt Cereal product V L₂ Oven h = 55 W/m².K T_= 300°C
A 1.5m diameter spherical balloon containing air at (K + 10) kPa is cooled such that the volume is reducedby 25%. For the process, the pressure is proportional to the square of the sphere’s diameter. What is the workdone by the surrounding? IMPORTANT NOTE: K=821
After going through the production process, thin plates with a length of 0.5m are cooled by suspending them vertically in a room with still air at 35°C. To maximize production throughput, the plates are hung as close together as possible. There is a concern however, that if the plates are too close together, the cooling will take longer, costing the company additional money. If the plates are initially at a temperature of 75°C, please answer the following: 1. What is the minimum plate spacing that would avoid interference between their free convection boundary layers? 2. What is the velocity in the x-direction at the upper edge of the plate?
kindly help me with this problem Enumerate and explain each briefly the FOUR (4) Properties of the Bernoulli Process
Metal spheres, 10 mm in diameter, are to be annealed by heating them to 827°C then allowing them to cool slowly in air at 27°C to the point where they are in thermal equilibrium with the air. 2000 balls are annealed in one hour’s time. What is the total rate of their heat transfer if they are made of steel, lead, or copper? a.Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
PROBLEM: IIC - 12 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
a cylindrical can of bean puree, has a diameter of 70 mm and height of 126 mm, and is initially at a uniform temperature of 25 ° C. The cans are stacked vertically inside a retort into which steam is introduced at 120 ° C. Calculate the temperature in the center of the can after a heating time of 0.55 h at 120 ° C. Now suppose the can is in the center of a vertical stack, insulated at its two ends by the presence of the remaining cans. (The heat capacity of the metal wall of the can can be neglected.) The heat transfer coefficient of steam is estimated to be 4640 W / m2 ° K. The physical properties of the bean are k = 0.750 W / m ° K and the thermal diffusivity = 2.007 x 10-7 m2 / s.a) Calculate the temperature in the center of the product.
PROBLEM: IIC-21 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
An eyed plate & pin is assembled as illustrated and are subjected to an opposing force of 10KN. The rod diameter & plate thickness is 6mm. The width of the plate is 20mm. A hole to which the pin is inserted is 8mm in diameter is located at the center of the plate. The plate is made of annealed SAE 1025 & the pin is high-heat oil quenched SAE 1095. (a) Determine if the assembly is safe to use; otherwise (b) Determine the safe load of the assembly.
Question : Studies show that the major energy consumption in Fijian villages is wood which is used for cooking over open fires. Typical consumption of wood is 1 kg person–1day–1. (a) Estimate the heat energy required to boil a 2-liter pot full of water. Assuming this to be the cooking requirement of each person, compare this with the heat content of the wood, and thus estimate the thermal efficiency of the open fire. (b) How much timber has to be felled each year to cook for a village of 200 people?Assuming systematic replanting, what area of crop must the village therefore set aside for fuel use if it is not to make a net deforestation? Hint: refer to Table 10.4. (c) Comment on the realism of the assumptions made, and revise your estimates accordingly. Answer: (a) mcDT ≈ 0.6 MJ (heat losses from pot imply actual requirement is higher). h ≈ 3%. (b) 70 tonnes; 7 ha.