A hollow steel shaft 2304mm long is to be designed to transmit a torque of 28350 kJ. The shear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the length of the shaft is must not exceed 6 degrees. And the shear stress in the shaft must not exceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?

A hollow steel shaft 2304mm long is to be designed to transmit a torque of 28350 kJ. The shear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the length of the shaft is must not exceed 6 degrees. And the shear stress in the shaft must not exceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.15P: A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner...

See similar textbooks

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is 2/3 of the outside diameter and if G = 83 GPa, find the angle of twist in degrees if the shaft is 5 meters long.
1. A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the maximum shear stress acting on it, if the twist in the shaft is not exceeding 1° in 2 m length of the shaft. Take modulus of rigidity as 102 GPa.
Ahollow shaft with an external diameter of 150 mm transmits a maximum torque of 13 kNm. The shaft length is 5 m,and the maximum shear stress is limited to 40 MPa. If G = 84 x 103N/mm2, calculate;2.1 the internal diameter of the shaft.2.2 the angle of twist in degrees.2.3 the minimum shear stress in the shaft.