A horizontal jet of water 2x103 mm2 cross-section and flowing at a velocity of 15 m/s hits a flat plate at 60o to the axis (of the jet) and to the horizontal. The jet is such that there is no side spread. If the plate is stationary, calculate a) the force exerted on the plate in the direction of the jet and b) the ratio between the quantity of the fluid that is deflected upwards and that downwards. Assume that there is no friction and no shear force.

A horizontal jet of water 2x103 mm2 cross-section and flowing at a velocity of 15 m/s hits a flat plate at 60o to the axis (of the jet) and to the horizontal. The jet is such that there is no side spread. If the plate is stationary, calculate a) the force exerted on the plate in the direction of the jet and b) the ratio between the quantity of the fluid that is deflected upwards and that downwards. Assume that there is no friction and no shear force.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the following figure showing a jet of water supporting a weight of 100 N at aheight of 5 m . Water leaves the nozzle with a velocity of 20 m/s. The diameter d ofthe nozzle will be
Water (density 1000 kg/m3) is flowing past a long cylinder at 1 m/s. The cylinder has a diameter of 0,05 m and a length of 0,4 m. The axis of the cylinder is perpendicular to the distraction of flow. What is the force on the cylinder in N?
A viscous laminar fluid between two parallel plates is driven by the top plate moving at a constant speed Uo. TIle bottom plate, distance b apart, is fixed. If the plates are separated by a distance of 5 cm and the top plate travels at a constant speed of 35 m/s. Find the discharge per unit width.
In a machine a Newtonian fluid is filled in the clearance between a shaft and a concentric sleeve. The sleeve attains a speed of 50 cm/s, when a force of 40 N is applied to the sleeve parallel to the shaft. What is the speed if a force of 200 N is there?
An incompressible fluid (density 1000kg/m3) is flowing through a pipe with a constriction. The pipe is on an angle of 30 degrees with the narrow section at at distance of 10m from the wide section and lower that the wide section . The speed of the fluid in the wide section is 2m/s and 10m/s in the narrow section, I f the pressure in the wide section in 250 kPa. What is the pressure of the fluid in the narrow section ?
Water fills a cylindrical tank to depth h . The tank hasdiameter D . The water fl ows out at average velocity V o from a hole in the bottom of area A o . Use the Reynoldstransport theorem to fi nd an expression for the instantaneousdepth change dh/dt .
The water jet -13.5 cm in the figure strikes normal to a fixed plate. The velocity of the jet is -8 m/s. Neglect gravity and friction. Compute the force Fin newtons required to hold the plate fixed. * N Plate
For a horizontal water jet having a velocity of 25 m/s strikes a vertical stationary flat plate. The water splatters in all directions in the plane of the plate. How much force is required to hold the plate against the water stream? Assume diameter of pipe is 6 cm
A river discharges into a reservoir at a rate of 400,000 ft/s (cfs), and the outflow rate from the reservoir through the flow passages in the dam is 250,000 cfs. If the reservoir surface area is 40 mi?, what is the rate of rise of water in the reservoir?
A conveyer belt is installed in a process industry to move the product from bottom to top. Anincompressible, viscous fluid is placed between the upper and lower belts to avoid the friction andcool down the surface of belt. The belts are aligned at an angle θ and moving in opposite directionwith constant velocities V1 and V2, as shown in figure. Assume the laminar flow with no pressuregradient and gravity acting vertically downward. Calculate:a. Velocity profile in the fluidb. Volume flow rate between the beltsc. Shear force per unit area acting on bottom belt Note: Enlist all the assumptions you have taken to solve the problem and clearly mention theboundary conditions.
Air is flowing parallel to the plate at U∞=5 m/s and T∞=300 K over the flat plate of length L=0.1 m anddepth of 1 m into the paper, at the atmospheric pressure at the same temperature as the plate. Find;a) Boundary layer thickness at the point x = L of the plateb) Find the total resistance force acting on the two surfaces of the plate.c) The velocities in the hydrodynamic boundary layer are measured by a hot wire anomemeter. Thevelocity at x=0.1 m on the x component is measured as u=3 m/s. Find the distance from the plate and they component of velocity v.
-, Given: Water from a pressurized tank flows out and creates a vertical jet as shown. Total head loss due to friction is 5 m At location A. a pump adds 20 J/kg in the direction of flow to the stream Water properties are as follows: p= 998 kg/m and u= 1E-3 Ns/m. Acceleration due to gravity is g= 9.81 m's?. Find: Maximum height H to which the jet rises. Air 75 kPa (gage) H? Water 85 cm