A large reservoir supplies water for a community. A portion of the water supply system is shown. Water is pumped from the reservoir to a large storage tank before being sent on to the water treatment facility. The system is designed to provide 1310 L/s of water at 20°C. From B to C the system consists of a square-edged entrance, 760 m of pipe, three gate valves, four 45° elbows, and two 90° elbows. Gage pressure at C is 197 kPa. The system between F and G contains 760 m of pipe, two flanged open gate valves, and four 90° regular flanged elbows. All pipe is 508 mm diameter, cast iron. Calculate the average velocity of water in the pipe, the gage pressure at section F, and the power input to the pump (its efficiency is 80 percent). P8.169 B I = 174 m 152 m Pump z = 104 m z=91 m. C

A large reservoir supplies water for a community. A portion of the water supply system is shown. Water is pumped from the reservoir to a large storage tank before being sent on to the water treatment facility. The system is designed to provide 1310 L/s of water at 20°C. From B to C the system consists of a square-edged entrance, 760 m of pipe, three gate valves, four 45° elbows, and two 90° elbows. Gage pressure at C is 197 kPa. The system between F and G contains 760 m of pipe, two flanged open gate valves, and four 90° regular flanged elbows. All pipe is 508 mm diameter, cast iron. Calculate the average velocity of water in the pipe, the gage pressure at section F, and the power input to the pump (its efficiency is 80 percent). P8.169 B I = 174 m 152 m Pump z = 104 m z=91 m. C

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

What will result from too little EGR flow? And what can cause a reduction in the flow?
Water is to be pumped to an atmospheric rooftop storage tank atop a 5-story building, 75 feet above ground-level. A pump station is located at the ground-level. The suction line is a 2-inch ID commercial steel pipe tapped into a municipal supply line maintained at 50 PSIG 5 feet below ground-level. The discharge line is 1.5-inch ID commercial steel, and the total length of pipe is approximately 100 ft. There are two ball valves, a water meter, and gate valve on the discharge line. Determine the pump head required to deliver 40 GPM and the pump power that must be supplied to the water. If a pump is required, what is the motor power required if the pump operates at 55% efficiency?
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a.75 kPA b.225 kPa c.150 kPa d.100 kPa With F.B.D
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a.225 kPa b.100 kPa c.75 kPA d.150 kPa PLEASE INCLUDE FIGURE OR FBD
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
Please include a diagram.A pump supplies water at a flow rate of 4ft3/s from an open reservoir through a horizontal 8-in sched 40 pipe. The head loss from the reservoir to the suction of the pump is 2 ft-lbf/lbm, and the discharge is at 90 psig into a 6-in sched 80 pipe. The pump has an efficiency of 65% answer the following:a.) The head that must be delivered by the pump to the water is ________ or energy developed by the pump or output energy of the pumpb.) input energy to the pumpc.) Rated power of the pump in kW
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discharge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023. Include the diagram in your solution. a.100 kPa b.150 kPa c.75 kPA d.225 kPa
Lukewarm water at 60 degree c in a storage tank is being pumped at 300 L/min from the tank. The line from the storage tank to the pump suction is 5 m of 2 inches Schedule 40 steelpipe, and it contains four (4) elbows. The discharge line after the pump is 50 m of 1.5 inches Schedule 40 steel pipe and contains a fully opened globe valve and two (2) elbows. The water was discharged to the households at 15 m above the water level in the storage tank. All elbows have a 90° angle. Calculate all frictional losses
Q3: Two tank are connected with piping system as shown. If the pump characteristics are given by: hp- 31-120000 and, 7p--190000Q+8590Q Where hp is in meters and Q in m³/s and np is the pump efficiency (%).Estimate the operational cost of the pumping (10000) m² of water to the upper tank if the cost of IKwh is 2000 ID. Neglecting the minor losses. H=15mm 0-150mm
Q1/ liquid is pumped from a ground level reservoir to an overhead tank through a 5 cm ID pipe as shown in Fig. (1): i. What pressure developed by the pump to 45° elbow 8 m Fig. (1) Globe valve Tank 5 m supply water to the tank at the rate of 245 I/min? ii. What is the power required for the pump, if the pump is only 62% efficient? iii. Calculate the available NPSH. If the pump required 12 m NPSH is it suitable to prevent cavitation for this system? why? Given that: u = 0.0016 Pa.s; p 850 kg/m', e/d 0.0035, (Le/d) of Globe valve (open) = 240 (Le/d) of 45° ēlbow = 24 and Pv = 36.6 kPa 25 m 45° Reservoir 45° elbow
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour