A multiflex flexible coupling, transmitting 15 kW power at 720 rpm, is shown in Fig. 9.46. It consists of two flanges keyed to the driving and driven shafts and connected together by means of a mumber of coils. The coils are placed in the slots on the periphery of the flanges at a distance of 30 mm from the axes of the shafts. The coils have a rectangular cross-section 4 x 2 mm and are made of steel FeE 220 (S, = 220 N/mm²). The factor of safety is 2.5. Calculate the required number of coils.

A multiflex flexible coupling, transmitting 15 kW power at 720 rpm, is shown in Fig. 9.46. It consists of two flanges keyed to the driving and driven shafts and connected together by means of a mumber of coils. The coils are placed in the slots on the periphery of the flanges at a distance of 30 mm from the axes of the shafts. The coils have a rectangular cross-section 4 x 2 mm and are made of steel FeE 220 (S, = 220 N/mm²). The factor of safety is 2.5. Calculate the required number of coils.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axes are at 60o to each other. Produce a graph of velocity ratio against angle for ? to proof the calculated results.
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys.
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys. Note: Sketch the belt drive system for both parts and label the given data on it.
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 2000 rpm. It has outer and inner radii 10 cm and 8 cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08 N/mm“. Assume coefficient of friction as 0.25.
The width of the belt used if its thickness is 6 mm. Ans. 261 mm 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt speed of 25 m/s. The belt has a mass of 2 kg/m of the belt length. The belt is used in a crossed configuration to connect a 300 mm diameter driving pulley to a 900 mm diameter driven pulley at a shaft spacing of 6 m. A. Calculate the belt length and the angles of wrap. Ans. 13.95 m, 3.34 rad or 191.4° B. Compute the belt tensions based on a coefficient of friction of 0.33. Ans. 1.76 KN, 1.96 KN
Q2 / A shaft transmitting 15kW at 200r.p.m. are supported by two bearings placed 1 m apart. A 600 mm diameter pulley is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25kN. Another pulley 400 mm diameter is placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt having maximum tension of 3.376kN, which is placed horizontally to the right. The angle of contact for both the pulleys is180° and =0.24. Determine the suitable diameter for a solid shaft if the bending moment acting on the shaft is reversed, allowing working stress of 42MPA in shear for the material of shaft and have yield stress of 400MPA and ultimate stress of 500MP.. And design the keys which support each pulley if the material of the keys is the same for the material of shaft.
5. Design a sleeve coupling for the transmission of 12 kW at 300 rpm by two connected steel shafts. Take service factor KS 1.25. The sleeve is made of CI. The key and the shaft are made of the same material. Allowable stress: Shear stresses in key and shaft 50 MPa Crushing stress in key= 100 MPa Shear stress in CI sleeve = 10 MPa
Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a distance of 12 m from the driving pulley of 480 cm diameter ?
A 6-in-wide polyamide F-1 flat belt is used to connect a 4-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 3. The center-to-center distance is 8 ft. The angular speed of the small pulley is 1850 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, F1a, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
Question No.15: Design muff coupling to connect two steel shafts transmitting 40 kW at 350 rpm. The material for shafts and key is plain carbon steel for which allowable shear and crushing stresses are 40 MPa and 80 MPa respectively. The material for muff is cast iron for which allowable shear stress is 15 Mpa