A pair of straight bevel gears, mounted on shafts which are intersecting at right angles, consists of a 24 teeth pinion meshing with a 32 teeth gear. The module at the large end of the tooth is 5 mm. Calculate : 1. the pitch circle diameters of the pinion and the gear; 2. the pitch angles for the pinion and gear; 3. the cone distance;

A pair of straight bevel gears, mounted on shafts which are intersecting at right angles, consists of a 24 teeth pinion meshing with a 32 teeth gear. The module at the large end of the tooth is 5 mm. Calculate : 1. the pitch circle diameters of the pinion and the gear; 2. the pitch angles for the pinion and gear; 3. the cone distance;

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
Compute the values for all the geometrical features for a pair of straight bevel gears having a diametral pitch of 8, a 20° pressure angle, 16 teeth in the pinion, and 48 teeth in the gear. Specify a suitable face width. The shafts are at 90°. tad wo m that ratates at1750 com
Solve this problem in spur gearsA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressureangle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate theaddendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. Ifthe center distance isincreased by 0.125 in., what are the new valuesfor thecontact ratio and thepressureangle with complete solution and write in hand writing thank you
A 28-tooth spur pinion mates with a 42-tooth gear. The diametral pitch is 4 teeth/in and the pressure angle is 20.. Make a drawing of the gears showing one tooth on each gear. Find and tabulate the following results: the addendum, dedendum, clearance, circular pitch, tooth thickness, and base-circle diameters; the lengths of the arc of approach, recess, and action; and the base pitch and contact ratio.
A 21-tooth spur pinion mates with a 28-tooth gear. The diametral pitch is 3 teeth/in and the pressure angle is 20°. Make a drawing of the gears showing one tooth on each gear. Find and tabulate the following results: the addéndum, dedendum, clearance, circular pitch, tooth thick- ness, and base-circle diameters; the lengths of the arc of approach, recess, and action; and the base pitch and contact ratio.
A pair of helical gears are machined with a hob. The hob has a 20 degree pressure angle and machines circular pitch of 0.55 inch/tooth on a spur gear. Two gears are machined, the pinion has 18 teeth and the gear has 36 teeth. The measured transverse diametral pitch on the pinion is 5 inch/tooth. The pinion transmits 10 hp at 1,000 rpm. Calculate the center distance of the gearset, in inches
A pair of helical gears are machined with a hob. The hob has a 20 degree pressure angle and machines circular pitch of 0.55 inch/tooth on a spur gear. Two gears are machined, the pinion has 18 teeth and the gear has 36 teeth. The measured transverse diametral pitch on the pinion is 5 inch/tooth. The pinion transmits 10 hp at 1,000 rpm. Calculate the helix angle of the gearset, in degrees.
4. A pair of spur gears with a centre distance of 495 mm is used for a speed reduction of 4.5:1. The module is 6 mm. Calculate the number of teeth on the pinion and the gear.
A gearset consists of a 16-tooth pinion driving a 40-tooth gear. The diametral pitch is 2, and the addendum and dedendum are 1/P and 1.25/P, respectively. The gears are cut using a pressure angle of 20°. (a) Compute the circular pitch, the center distance, and the radii of the base circles. (b) In mounting these gears, the center distance was incorrectly made in larger. Compute the new values of the pressure angle and the pitch-circle diameters.
A pair of steel gears have a design life of a million cycles. They have 20° full-depth teeth with a diametral pitch of 8. Both gear and pinion are made of steel heat-treated to 350 Bhn, and both have a face width of 1.0 in. The teeth are machined with the highest quality hobbing operation. The pinion has 35 teeth and rotates 2000 rpm. The gear diameter over pinion diameter ratio is 2. The gears stay below a temperature of 140 °F. Assume a mounting correction factor of Km = 1.6 and an overload factor of Ko = 1. Use a reliability of 99.9% and a safety factor of 1.5. Use the pinion for the bending fatigue calculations and assume that there is no load sharing. A. What is the fatigue strength for these conditions. B. What is the tangential force acting on the gear teeth? C. Estimate the horsepower that can be transmitted, based only on bending fatigue.
1. The figure shows a pair of shaft-mounted spur gears having a diametrical pitch of 6 teeth/in with a 14 tooth pinion (gear 2) driving a 49 tooth gear at a pressure angle of 20°. The power input is 3/4 hp at 2400 rpm cw. A, B, C, and D are bearings. 3. 3 in 3 in Determine the following: a. The Free Body Diagram for both gears. b. The pitch diameters of gears 2 and 3. c. The transmitted load. d. The torque Tin on the pinion shaft. e. The radial and tangential forces on gear 3 f. The output torque of gear 3 shaft.
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3