A pressure vessel has'a wall thickness of 8mm and a diameter of 300mm, What is the longitudinal stress if the pressure in the vessel is 4MPA? A 37.5 MPa 37.5 kPa 75 MPa 75 kPa Last s

Q: 10 mile/h = ……… m/s (1mile = 1852m) Convert from FPS to SI.

A: Velocity, V = 10 miles/h 1 mile = 1852 m

Q: Find the value of stress Force=0.889 N Area 0.1 mm2

A: Given data : Force=F Area=A   Required: Stress

Q: Q10: o ( stress ) is defined as: b: a forces per unit are a: strain c: change of length d: a force

A: Explaining stress.

Q: Given the following duty record, how much life is consumed at each stress level? 60 ksi 49 ksi 10…

A: An S-N curve establishes the number of cycles required to cause failure when a material is…

Q: T=100 Ib 3

A:

Q: Cable A Smooth 140 R

A: Drawing the Free body diagram of the given system, Since the block is connected with a single cable…

Q: Stress is directly proportional to strain within the proportional limit is Boy's Law 2 Hooke's Law…

A: Relation between stress and strain is given by Hooke's law. According to that law, Stress in the…

Q: The maximum shear stress (in MPa) in the

A: Given;  A cylindrical tank of;  Inner radius,r=7 mm  Thickness=50 mm  Gauge pressure= 2 MPa…

Q: A hydraulic cylinder has a 750 mm diameter. How much force (kN) can be developed with 275 kPa oil…

A: Given    Pressure, P = 1275 kPa  Diameter, d = 750 mm                     = 0.75 m Find   Force…

Q: Air p = 2 psi B A Water find the pressure at point C. 1 ft 4 ft 2 ft C SG = 0.9

A:

Q: 1. In reinforcing a pressure vessel, which of the metal metal following is hoop strip correct? Why?…

A: Pressure vessel with metal hoops as a reinforcement is the best choice due to following reasons:

Q: VB PB 30 A 2)

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: 10 MPa - 30 MPa 70 MPa 70 MPa 30 MPa 10 MPa a) 20MPa b) -20 MPa c) 63,54MPa d) -63,54MPa e) 40 MPa

A:

Q: A-20 in Oil SG 0.86 51t 0.8 t A-50 in. SG 2.5

A:

Q: Consider someone at the gym is lifting weight with a quadriceps extension: Derive equations and…

A: When the shin pad is farthest from the knee the torque applied to lift the weight is Torque =…

Q: If V is 20 m/s, what is H? (Note: Hg is mercury) AD DO NOT L NOUPLOAD TO po NOT DecloT UPLOAL UPLO…

A:

Q: Madde P (kPa) T ('C) Faz tanımı H,O 10000 100 300 Dovmuş sıVI

A: From the steam table, At P=10000 kPaTsat=310.997 °CAnd the given T=100 °C,T<TsatHence At P=10000…

Q: 7. Where do the maximum BM óččurs for th 10 KN B A 2M 3M a) -54 kNm b) -92 kNm c) -105 kNm d) – 65…

A: Consider a cantilever beam that has fixed support at A. A transverse uniformly distributed load of…

Q: A folloing og strer: oR=75 mpa, Oy = 15 mpa てx-355mia amle elemónt is geuljeefed fo the binanial 11

A: Givenσx=75MPaσy=15Mpaτxy=35MPaallowable  shear stress τa=95MPa

Q: Given the following duty record, how much life is consumed at each stress level? 60 ksi 49 ksi 10…

A:

Q: The value of stress amplitude (in MPa) i

A: Given, Minimum stress,σmin=200 MPaMaximum stress,σmax=400 MPaFind the value of stress amplitude ?

Q: 2) = 20KN S=3 Sy = 960 lPa Bobt joint mthoud clearance Findi d

A: Given data: P=20 kNs=3Sy=460 MPa Need to determine the diameter of the rivet.

Q: Esteel=20Ewood- Owood = 10 MPa. OSteel= 150 MPa wood Steel \00 mm

A:

Q: a. Discuss the graph of Load, W against energy losses (Whi-Wh2).

A: We have given

Q: 15 MPa 30 MPa 45 MPa 45 MPa 30 MPa 15 MPa a) -63,43 b) -42,28 c) 26,63 d) 57,35 e) 41,2 15

A:

Q: 10 kN 4 Smart 3 soi non 12 kN 8 kN 6 kN Aqu.21 Azn Iml F

A: Given

Q: In the given figure, the 300 N load is balanced by a force F in both systems. Assuming efficiencies…

A: Draw FBD for both the pully system.

Q: ne shear stress in

A:

Q: greatest draft and compression stresses

A: GIVEN :- P=8000 N To calculate the greatest draft and compression stresses. FIGURE:-   SOLUTION :-…

Q: CApans the temperature increase it would that number from the temperature er this contact and…

A:

Q: 30N/m 0.4kg Wwww

A: For solution refer below images.

Q: ckness of th SS yield stress SS = T A ga:

A:

Q: p = 2 psi SG = 0.9 Air 1 ft 4 ft 2 ft A Water

A:

Q: Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside…

A:

Q: It equal and opposite forces applied to a body tend toelongate it, the stress so produced is called…

A:

Q: Fi= 3 KN A <作る- 2KNT de 8 c=18 とるcm a= 22 m Fu= 20 KN Eト)=30° FB= 2 KN

A:

Q: A 3. 3m By Section Mothoc

A: Method of Section: Procedure: 1.Calculate support reactions due to load applied by adopting…

Q: 400mm Kerosene, SG 0.82 Air, SG=0.0012 Benzene, SG= 0.88 100mm 200rn 150mm 90mm Water Hg What is the…

A: It is required to determine the pressure difference between pipes of air(A) and pipes of benzene(B)

Q: 5 applications

A: Write: Examples of application of shear stress

Q: A compressed gas cylinder for use in mechanical engineering laboratory has an internal gage pressure…

A:

Q: A wind generator is installed. It is determined that the capacity factor of the installation is 29%…

A:

Q: Question 1 Ia. You want to draw water from a stream running down a hill behind your hoūse at a rate…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: A combine 9.3' of water, 6.5' of oil (SG = 0.71), and 5.0' of air at 26 psig and 70 deg F. What is…

A: Height of water, hw=9.3 ftHeight of oil, ho=6.5 ftHeight of air, hair=5.0 ftSpecific gravity of oil,…

Q: r. Take E=80 GPa.

A: 0.85mm

Q: lief valve is 1.5mpa, and the load pressure is 1MPA when the the cylinder piston is moving. a) The…

A: 1.Because point a and b pressure relief valves are present, the pressure during movement will be…

Q: Give data : Stress=23 N/mm2 Force=5 N Find cross sectional area

A: Given data : Stress=σ Force=F   Required : Cross sectional area

Q: Given: A = 51% B = 1015 hPa C = 838 hPa

A: Given data: Internal Diameter of bottle = D = 6 cm Internal height of bottle = HB = 25 cmLength of…

Q: What is the contact force between the boxes? (There is no friction.) F m 3m 2F

A:

Q: 20 MPa 100 MPa 40 MPa What is the average stress? A 60 MPa

A: Given:

Q: H.W.: As shown in figure below, determine the pressurt point A. Hg Ans. : (2.164 Kla Vacuum Water…

A: As per the given data and the standard values of density, the answer I got is absolutely correct.…

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.