A process sampled 20 times with a sample of size 8 resulted in = 28.5 and R = 1.8. Compute the upper and lower control limits for the x chart for this process. (Round your answers to two decimal places.)UCL = 29.17LCL = 27.82XCompute the upper and lower control limits for the R chart for this process. (Round your answers to two decimal places.)UCL = 3.35XLCL =0.24

Given data Sample size (n) = 8 x¯¯=28.5R¯=1.8

Answered: A process sampled 20 times with a…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

A process sampled 20 times with a sample of size 8 resulted in = 28.5 and R = 1.8. Compute the upper and lower control limits for the chart for this process. (Round your answers to two decimal places.) UCL = LCL = Compute the upper and lower control limits for the R chart for this process. (Round your answers to two decimal places.) UCL = LCL =
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of x? = x= 156.76 mm (round your response to two decimal places). b) What is the value of R? R= mm (round your response to two decimal places). Day 1 2 3 4 5 Mean x (mm) 158.9 155.2 155.6 157.5 156.6 Range R (mm) 4.2 4.4 4.3 4.8 4.3
A process has a mean of 9.20 grams and a standard deviation of .30 gram. The lower specification limit is 7.50 grams and the upper specification limit is 10.50 grams. Compute Cpk
Resistors for electronic circuits are manufactured on a high-speed automated machine. The machine is set up to produce a large run of resistors of 1,000 Ohms each. To set up the machine and to create a control chart to be used throughout the run, 15 samples and their measured values are as follows: Sample Number Readings (in Ohms) 1 1010 991 985 986 2 995 996 1009 994 3 990 1003 1015 1008 4 1015 1020 1009 998 5 1013 1019 1005 993 6 994 1001 994 1005 7 989 992 982 1020 8 1001 986 996 996 9 1006 989 1005 1007 10 992 1007 1006 979 11 996 1006 997 989 12 1019 996 991 1011 13 981 991 989 1003 14 999 993 988 984 15 1013 1002 1005 992 Develop three-sigma appropriate control chart(s) from the chart(s) what comments can you make about the process? Explain and show work
Boxes of Honey-Nut Oatmeal are produced to contain 14.0 ounces, with a standard deviation of 0.10 ounce. For a sample size of 49, the 3-sigma x chart control limits are: Upper Control Limit (UCL) = Lower Control Limit (LCL) = ounces (round your response to two decimal places). ounces (round your response to two decimal places).
Boxes of Honey-Nut Oatmeal are produced to contain 14.0 ounces, with a standard deviation of 0.15 ounce. For a sample size of 36, the 3-sigma x chart control limits are: Upper Control Limit (UCL;) = ounces (round your response to two decimal places). Lower Control Limit (LCL;) = ounces (round your response to two decimal places).
Sample size (n) is 16, mean of the sample means ( ) is 15, mean of the sample ranges ( ) is 6, and population standard deviation ( ) is not known. Calculate the UCL and LCL of the mean chart (x-Chart) for this process. Group of answer choices Cannot be calculated UCL=33.0, LCL=-3.0 UCL=13.73, LCL=16.27 UCL=16.27, LCL=13.73 UCL=33.0, LCL=0
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of X? x= mm (round your response to two decimal places). Day 1 2 3 4 5 Mean x (mm) 158.9 155.2 155.6 157.5 156.6 Range R (mm) 4.2 4.4 4.3 4.8 4.3
Arana is a company that produces homemade Rotini pasta. They use statistical process control to monitor the manufacturing process. The company collects five samples, each containing six packs of pasta. Below is the sample data, but the standard deviation of the process output is unknown. If an R chart is created using three-sigma limits (i.e., z = 3) to monitor the variability of products, what would be the upper control limit for this R chart? Sample 1 Sample 2 Sample 3 Pack 1 452.3 451.6 448.6 Sample 4 454.7 Sample 5 448.9 7.614 9.328 11.653 13.427 Pack 2 452.8 451.2 455.6 451.7 453.4 Pack 3 456 454.6 456.5 451 456.7 Pack 4 457.2 455.3 451.9 452.6 456.3 Pack 5 457.8 452.2 455.6 454.7 452.4 Pack 6 451.8 451.9 448.3 458.4 456
Refer to Table S6.1 - Factors for Computing Control Chart Limits (3 sigma) for this problem. West Battery Corp. has recently been receiving complaints from retailers that its 9-volt batteries are not lasting as long as other name brands. James West, head of the TQM program at West's Austin plant, believes there is no problem because his batteries have had an average life of 45 hours, about 10% longer than competitors' models. To raise the lifetime above this level would require a new level of technology not available to West. Nevertheless, he is concerned enough to set up hourly assembly line checks. Previously, after ensuring that the process was running properly, West took samples of 5 9-volt batteries for 25 test to establish the standards for control chart limits. Those 25 tests are shown in the following table: Sample Data Sample Data Hour Sample Taken 1 2 This exercise contains only parts a and b. = a) For the given data, the x = 1 2 3 4 5 6 7 8 9 10 11 12 13 3 4 5 X R 47 44 36…
1. An ad agency tracks the complaints, by week received, about the billboards in its city: Week No. of Complaints 1 8 2 4 3 11 4 16 5 8 6 9 This exercise contains only parts a, b, and c. a) The type of control chart that is best to monitor this process is c minus chartc−chart . b) Using z = 3, the control chart limits for this process are (assume that the historical complaints rate is unknown): UCLc =?complaints per week (round your response to two decimal places). LCLc =?complaints per week (round your response to two decimal places).
Refer to Table S6.1 - Factors for Computing Control Chart Limits (3 sigma) for this problem. Twelve samples, each containing five parts, were taken from a process that produces steel rods at Emmanual Kodzi's factory. The length of each rod in the samples was determined. The results were tabulated and sample means and ranges were computed. The results were: Sample Mean (in.) Range (in.) Sample Sample Sample Mean (in.) Range (in.) 1 9.404 0.044 7 9.403 0.021 2 9.402 0.051 8 9.405 0.058 3 9.393 0.042 9.395 0.039 4 9.404 0.037 10 9.401 0.038 9.399 0.048 11 9.401 0.054 9.397 0.053 12 9.404 0.061 For the given data, the x = inches (round your response to four decimal places). Based on the sampling done, the control limits for 3-sigma x chart are: Upper Control Limit (UCL;) = inches (round your response to four decimal places). Lower Control Limit (LCL;) = inches (round your response to four decimal places).

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS