(a) Recall that the simulated ROM of our computer is 16 x 4 bits. If we had 32 x 4bits ofROM, would it be possible for us handle all of the instructions with our current setup? If yes/nothen why?(b) If our current setup does not allow us to handle all instructions in the 32 x 4bits ROM, are there1.any specific modifications that would allow us to?

The present ROM of the computer is 16X4 bits. The ROM of the computer is changed to 32Xa bits. Two…

Answered: (a) Recall that the simulated ROM of…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

List and describe two AVR instructions. As part of your description make sure that you list the operation for each instruction that is provided in the instruction set summary.
A) List and describe 10 features of the Atmel ATmega 2560 AVR microcontroller (use the ATmega 2560 complete reference manual for help). B) List and describe two AVR instructions. As part of your description make sure that you list the operation for each instruction that is provided in the instruction set summary.
Q1// What are the difference between Logic Devices and Programmable Logic Devices? Q2// Explain the advantage's of Programmable Logic Devices? Q3// List the disadvantages of Fixed function logic devices. Q4// Compare between Logic Devices and Programmable Logic Devices?
Q1) List the procedural steps taken by the microcontroller when a call to service routine was occurred. Q2) What is the term “Reduced Instruction Set Computer (RISC)” mean in the Microcontroller Architecture. Q3) What should the microcontroller do in order to execute an instruction. Q4) What are the necessary buses used within the microcontroller Architecture.
4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
Explain the SUB instruction of 8086. Compare it with SBB instruction. Write a Assembly language program for 8086 to find the square root of a number using SUB instruction. (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) A BIE
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
1. Study this program, then answer the questions that follow: MOV AL, 64H ADD AL, 27H DAA a) What does the accumulator contain immediately after the ADD instruction is executed? What do the CY and AC flags contain? b) What does the accumulator contain after the DAA instruction is executed? What do the CY and AC flags contain?
Assume that the microprocessor can directly address 1M with a and 8 data pins. The maximum RAM system can design by using the following RAM chips is given in the below table. Choose the correct option:(provide answer in details) (a) None of them (b) 25K x 8 (c) 27K x 8 (d )26K x 8 (e) 24K x 8
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
1- Explain the meaning and operation of CMC instruction ? 2. The Instruction Pointer is bits in length. a) 8 bits b) 4 bits c) 16 bits d) 32 bits
a) In Assembly programming what is the functionality of the following instructions DECFSZ ВTESC MOVLW MOVWF goto b) A piece of code is required for a time critical activity. Should this be written in assembly language or C? Explain your answer. 5 Explain the difference between the (For) and (While) loops. Highlight the main components of the (For) loop that are required for its execution. Consider the following C program designed to run on a PIC 18F4455. int main(void) 2 { 1 double voltage; double current; double milliwatts; double energyUsed; double cummulativeEnergy = 0; while (1) { voltage=analogRead (VOLTAGE_PIN)*voltageScaleFactor; current=analogRead (CURRENT_PIN)*currentScaleFactor; milliwatts=voltage*current; energyUsed=milliWatts*0.5; cummulativeEnergy=cummulativeEnergy+energyUsed; 10 11 12 13 14 15 _delay_ms (500); 16 } 17 a) What is the role of the symbols "{" and "}" b) The code here is indented. Explain the importance of indentation N m 4 n Or 00 o A m

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS