A rectangular concrete channel 5m wide carries water as shown in the figure. The channel bed slope is 0.0022. Find the theoretical rate of flow in the channel.

Q: A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural mem...

A:

Q: Write the shear and moment equations (simplified and not simplified) at each segment of the beam. Dr...

A:

Q: In a falling head permeability test drop in head Occurs from 60 m to 40 m in 10 minutes. The cross-s...

A:

Q: The perpendicular offset of the PT of a simple curve is 120.20m. If the angle of intersection is 50֯...

A:

Q: Sir Isaac Newton discovered that any two masses m, and m, attract each other with a force that is eq...

A: What are the appropriate units for G, if the preceding equation is to be homogeneous in units?

Q: A machine having a first cost of Po0,000 s computed using constant percentage of the declining book ...

A:

Q: 30 KN/m A B 3.00 m 6.00m H 5 Panels@4.00 m = 15.00 meters PROBLEM NUMBER 1: In the given cantilever ...

A:

Q: Determine the load that can be applied at the end of the rigid bar if the stress either spring shown...

A: Step 1: Spring stiffness: Stiffness of first spring= 83 x 103 x 10^4/(8x150^3x20) =1.537 N/mm Stiffn...

Q: Locate the centroid of the shape shown in the figure. Make a final sketch. 50 cm 20 07

A:

Q: A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural mem...

A:

Q: Determine the stress in each of the two vertical rods if the temperatu °C after the load P=75 KN is ...

A: According to given data

Q: A reversed curve is to connect three lines thus forming the center line of a new road. The lines are...

A:

Q: Q3. Analyse the gable frame shown in FIG.3 by the slope deflection method. Draw the bending moment a...

A:

Q: the load is 150kN at the center of the beam and the dimension of the beam is 6''x6''x24''. compute f...

A:

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and ...

A: For the given rigid bar,

Q: A constant force F is applied for 3 s to change the particle's velocity from v1 to v2. Determine the...

A: Given data,  Time = 3 s V1 = 15 m/s V2 = 30 m/s To find out the force of F. 

Q: Consider the following simply supported beam with a concentrated dead load acting at a distance of 6...

A: Given,  L=18ft X=6ft Dead load = 38k Uniform live load = 2.7k/ft n=8 fc'=3000psi Our aim is to deter...

Q: Assume straight line instead of parabola for stress strain curve of concrete as follows and partial ...

A:

Q: ed concrete slab. Assume A 36 full lateral support of the lange. Unit weight of concrete is

A: Step 1dead load on beam ⇒DL =1×2.4×0.15×24 kn/m3            = 8.64 kn/m  step 2  ultimate factoreed ...

Q: Q.2) A simple beam of span length 3.2 m carries a uniform load of intensity 48 kN/m. The cross secti...

A: Given data:Span length=3.2 mUDL=48 KN/mEw=10 GPaEst=210 GPaσstallow=120 MPaσwoodallow=6.5MPa

Q: A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural mem...

A:

Q: A type of support which can stand alone: a. hinge b. roller C. link d. fixed

A:

Q: Use the substitute member to make a complete analysis of the complex truss shown.

A:

Q: through a V-notch weir. Determine the max nead of water on the weir , if vertex angle is 45° D 78 cm...

A: Discharge Q = 0.1 - 0.2 m3/sec Vertex angle = 450

Q: Unless otherwise stated, it is usually assumed that the azimuth of a line is measured

A:

Q: A horizontal parallel plate ESP consists of a single duct 4.8m height and 6m long with 30cm plate to...

A: Given, Collection efficiency,η=94.4% Inlet loading=144 grains/m3 Gas flow rate=95 m3/min Height=4.8 ...

Q: ,Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft³) behaves as a liquid. Determine the for...

A: Given data,  Specific weight = 125lbf/ft³ Height = 9ft Vertical braces spaced at = 2 ft  

Q: The angle of intersection of a circular curve is 45°30' and its radius is 198.17m. PC is Stationing ...

A:

Q: 5/103 Find the reaction at A due to the uniform loading and the applied couple. 2 kN/m 12 kN-m A 3 m...

A: Here vertical component of reaction at the point A is Ay, horizontal component of reaction at point ...

Q: Length of the long chord connecting P.C. and P.T.

A: We will solve this question in step no. 2

Q: 1. The document requested by the owner as a protection against the risk of the contractor not accept...

A:

Q: A rectangular flume of planned timber (n = 0.017) 22 ft. Wide, 950 ft. Long, with horizontal bed lea...

A:

Q: The back azimuth of a line whose true bearing is S 42* 15' W is: A.222* 15 B.132* 15 C. 42* 15' ...

A:

Q: Determine the mass of the heaviest uniform cylinder that can be supported in the position shown with...

A:

Q: Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wa...

A: To Determine Forces in the hangers at points B, C, and D so that the force couple system at point O ...

Q: In the design of beams for the limit state of collapse in flexure as per IS: 456-2000, let the maxim...

A:

Q: In the design of beams for the limit state of collapse in flexure as per IS: 456-2000, let the maxim...

A:

Q: A system of forces which produces zero moment: a. parallel forces b. space forces C. concurrent forc...

A: Given various system of forces are given. Parallel  forces Space forces Concurrent forces General fo...

Q: The given data shows a sieve analysis of the soil sample. Classify the soil according to AASHTO Meth...

A:

Q: find the coordinates of the point in the curve y^2=12x-2y+23 that is nearest to the point P(10,4)

A: To determine the coordinates of the point on the given curve that is nearest to the given coordinate...

Q: A machine is bought at P420,000 with an economic life of 6 years and a salvage value of P50,000. The...

A:

Q: A reinforced concrete beam, size 200 mm wide and 300 mm deep overall is simply supported over a span...

A:

Q: An impellar blade unit operates at 50 rpm. Determine the degree of mixing? Also if the blade operate...

A:

Q: For the figure shown, determine the horizontal and vertical components, respectively, of the hinge s...

A: Consider the member ABCD,

Q: Given the data of a compound curve with station of PI - 3+020, I₁-24°, D₁-6°, I₂-30° and D₂-7°, plot...

A: Sketch of the curve is given below with labelling and elements of the curve.

Q: 9. Using cantilever method, determine the maximum absolute axial force in the column in kN due to la...

A: Given data in question  Lateral loading Dimensions  Cantiler method  To find out  Axial forces in co...

Q: 8.17 The frame of the bow saw is a bent tube of 3/4-in. outer diameter and 1/16-in. wall thickness. ...

A:

Q: Q.2. Determine the centroid of the composite area shown in Fig.Q2. 5ft 4 ft 6 ft 5 ft Fig. Q2

A:

Q: The U-tube of Figure A contains mercury (s = 13.6) and given an acceleration of 1.22 m/s to the righ...

A:

Q: Determine the resultant and the direction (measured from positive x- axis) of the three forces actin...

A:

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.