A simplified Rankine cycle and some data are given in the figure below.a. Show the process in a TS diagramb. Calculate the rate of heat addition (QH) to the boiler.c. Calculate Wpump-d. Calculate |Wnetl.e. Determine the thermal efficiency (n)6 MPа,550 °CBoiler6 MPaw, (turbine)|mass flow rate (m): 22 kg/sTurbineTurbine efficiency(isentropic): 89 %w, (pump)34Condenser50 КРa50 kPaWorking fluid: water

Given, Conditions at the inlet of the turbine Enthalpy, Entropy, At condenser Turbine…

A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (Qw) to the boiler. c. Calculate Wrump- d. Calculate |Wne|- e. Determine the thermal efficiency (17) 6 MPа, 550 °C Boiler 6 MPa w, (turbine) mass flow rate (m): 22 kg/s Turbine Turbine efficiency (isentropic): 89 % - w, (pump) Condenser 50 kPa 50 КPa Working fluid: water

A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (Qw) to the boiler. c. Calculate Wrump- d. Calculate |Wne|- e. Determine the thermal efficiency (17) 6 MPа, 550 °C Boiler 6 MPa w, (turbine) mass flow rate (m): 22 kg/s Turbine Turbine efficiency (isentropic): 89 % - w, (pump) Condenser 50 kPa 50 КPa Working fluid: water

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Homework-2 Compute the themal e fficiency of an ideal Ran kine cycle for which the steam leavea the boiler as Saturated Vapor at 30 bars. The turbine-outlet Conditions is Be1 bar. Determine the mass floo rate of the steam in kg/hr, net Power output of the cycle is 50000 Sehematic ond given data are: 1f the kw. The TI= 5002 P 3०bars %3D 9in (saturated) vapour 30 bars 2 PR =0-1 bar 4 Pa=30 bas o-1 bar +4 Tout 3 (Saturated liquid) Wp ( Simple Ideal Power cycle) (T.S. diagram e)
Problem 3. A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (QH) to the boiler. c. Calculate Wpump- d. Calculate |WNet|- e. Determine the thermal efficiency (n.)
1.4 A diesel engine operating an air standard diesel cycle has 20cm bore and 30cm stroke. the clearance volume is 420cm3. if the fuel is injected at 5% of the stroke, find the air standard efficiency. 1.5 Develop an expression for the thermal efficiency of the air-standard diesel cycle as a function of the compression ratio r. = V1V2 and the expansion ratio r, = V4 / V3. Assume the working fluid is an ideal gas, and the volume effect of moles of gas generated is small relative to the effect of heating from combustion. %3D
3) The pump works (wbomba) and the turbine (wurbina). 4) The heats: boiler (QH) and condenser (QL). 5) The thermal efficiency of this cycle.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: PV and TS diagrams of the cycle showing ideal and actual process lines Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.___________________________
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Combined work (KW) . Ans.____________________________ Combined steam rate in kg/KW-hr. Ans.___________________________ Actual heat rate( KJ/KW-hr). Ans.____________________________
A simplified Rankine cycle and some data are given in the figure below.a. Show the process in a TS diagramb. Calculate the rate of heat addition (Q.H) to the boiler.c. Calculate ?w????.d. Calculate |WNet|.e. Determine the thermal efficiency (n?)
A turbine engine air intake is at pressure and temperature of air drawn 99 kPa and 29 °C respectively. The maximum pressure and temperature during the cycle is 990 kPa and 888 °C respectively. The adaibatic index as 1.4. After claculations, the pressure ratio of the cycle is compressor exit temperature is K, turbine exit temperature is K, net specific work output from the gas turbine engine is in k thermal efficiency_ is % and work ratio of the cycle is to I decimal place.
H.W2:-A) The bore and stroke of an internal combustion engine working on Otto cycle are (17 cm) and (30 cm) respectively. If the total volume is (8.825 cm3),find the air standard efficiency. Take X=1.4
3- A reaction turbine is supplied with steam at (60 bar, 600 C°). The condenser pressure is (0.07 bar). If the reheat factor can be assumed to be (1.04) and the stage efficiency is constant throughout at (80%). Calculate the steam flow required in (ton/hr) for a diagram power of (25 MW). (Ans. 75.6 ton/hr) The ctoam ntion at full load for a 12 MWV) turbine ic (1 S 6 ton /brl At balf lead the