A source of AC emf E₁ = 100/0º volts with an impedance of Z₁ = 20/0° ohms is connected in parallel with another AC source of E₂ = 100/53.10 volts with an impedance Z₂ = 20/0° ohms. The two AC source are use to supply a load impedance of Z₁ = 20/-900 ohms. Calculate the value of the load current I₁. O a. 10 amperes O b. 12 amperes O c. 4 amperes O d. 8 amperes

A source of AC emf E₁ = 100/0º volts with an impedance of Z₁ = 20/0° ohms is connected in parallel with another AC source of E₂ = 100/53.10 volts with an impedance Z₂ = 20/0° ohms. The two AC source are use to supply a load impedance of Z₁ = 20/-900 ohms. Calculate the value of the load current I₁. O a. 10 amperes O b. 12 amperes O c. 4 amperes O d. 8 amperes

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Q2. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. a = 50° TI 50 2 Vs = 300 sin 100zt ( cot T2 in cot
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9
Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100mH : 15 2 Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and / and state the relationship between Vs and I. (ii) (iv) Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load.
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Exercise-1 Vs = 240V 60Hz Is=10A/....... Power system Is ww R 1k0 Xc=-j/(2pi60x0.00016)=-1994 XL=ZL=j2pifl=j2pi60x0.142=j53.54 142mH Is=Ir+IL+Ic=.........=Vs/Ztotal=....... 160μF
9. A noninductive load with a resistance of 30 Q2 is connected in series with a capacitor. The capacitor has a capacitive reactance of 25 Q and negligible resistance. The series circuit is energized from a 210 V, 60 Hz source. Determine: a. the impedance of the series circuit. b. the current, in amperes. c. the loss in volts across the noninductive resistance load. d. the loss in volts across the capacitor.
Given the circuit shown, answer the following questions I 40 8n I3 Vs = 24/60° v E V2 -j4 n 12 one of the following statements is correct: Choose... 12 in Ampere equals to: Choose... the equivalent impedance in Ohm of the circuit is Choose... V2 in Volts equals to: Choose...
2)With reference to the waveform given below formulate the equation for the average value of DC voltage available across the load, if the load connected is a pure resistive load and if the circuit applicable tot his waveform is fed from a load having 180 volt 50 Hz start connected input with the value of resistance equivalent to 200 ohm solve and obtain the value of Dc power in the load (3 phase bridge) Van Vbn Vcn +Vm P 180° 210° 360° D3&D4 D5&D4 D5&D2 D1 & D2 D1&D6 D3 & D6 120° 120°
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002