A ternary signaling has three signals for transmission: mo : 0, mị : 2p(t), m2 : -2p(t). (a) If P(mo) = P(m1) = P(m2) = 1/3, determine the optimum decision regions and PeM of the optimum receiver as a function of E. Assume an AWGN channel. %3D (b) Find PeM as a function of E/N. (c) Repeat parts (a) and (b) if P(mo) = 1/2 and P(m1) = P(m2) = 0.25, %3D

A ternary signaling has three signals for transmission: mo : 0, mị : 2p(t), m2 : -2p(t). (a) If P(mo) = P(m1) = P(m2) = 1/3, determine the optimum decision regions and PeM of the optimum receiver as a function of E. Assume an AWGN channel. %3D (b) Find PeM as a function of E/N. (c) Repeat parts (a) and (b) if P(mo) = 1/2 and P(m1) = P(m2) = 0.25, %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An analog signal in sinus form is desired to be transmitted to the receiver with pulse code modulation. Instead of xxx given below, you write a value. Peak-to-peak amplitude = 10 volts Frequency of the signal = 100 Hz Mid-rise one-shaped quantizer: 8 levels Encode the bit strings you will create with Bipolar signaling. Encode the bit strings you will create with M=xxx multilevel pulse code modulation.
Explain the process of multiplexing at the transmitter and demultiplexing at the receiver (draw the block diagram)
An available channel for FM transmission is 30 kHz wide. The maximum allowable modulating signal fre- quency is 3.5 kHz. What deviation ratio should be used?
What are the similarities and differences between the information signal m (t) obtained as a result of demodulation and the original information signal m (t) on the modulation side? (first one is original signal)
The rate of change of the carrier frequency in an FM signal is determined by the a. carrier frequency b. modulating frequency c. carrier voltage d. modulating voltage
For the signal flow graph of the given figure consider the following statements: 1. It has three forward paths. 2. It has three individual loops. 3.lt has two non touching loops. out of above the correct statements are X2 O 1,2, 3 O 1,3 О 1,2 О 2,3
A signal is limited to the range peak to peak 10 V and frequency in the range (800 to 3300 Hz). The communication system is updated to allow increasing of about 50% above the old 64 quantization levels. Find the bandwidth if the quantized samples are transmitted either as binary ASK pules or as 16-level pulsed BW1=70 kHz, BW2=17.5kHz O BW1=73 kHz, BW2=20.5kHz O BW1=71 kHz, BW2=18.5kHz O BW1=72 kHz, BW2=19.5kHz O BW1=69 kHz, BW2=16.5kHz O
The modulating signal directly deviates the carrier's frequency in this angle modulation. Select your answer. Direct FM Indirect FM Indirect PM Direct PM
What are the similarities and differences between the information signal m (t) obtained as a result of demodulation and the original information signal m (t) on the modulation side? (the demodulated signal is irregular one)
9- In AM DSB/SC, the carrier is suppressed in order to: a) simplify the receiver design b) reduce the transmitter complexity c) increase the transmission efficiency 10-If the transmission channel is crowded, the preferable modulation to use is: a) AM-SSB b) AM-VSB c) AM-DSB d) FM 11- In AM-VSB, the vestige of the lower side band is important in order to: a) include the carrier wave to simplify the receiver design b) include the d.c. component of the message signal c) reduce the total bandwidth comparing with AM-DSB d) all of the above, and to increase transmission efficiency 12-Using Smith chart, if a piece of T.L. with a length of (lambda/4) is terminated with open-circuit, then its input impedance will be: a) open circuit b) short circuit c) inductive reactance d) capacitive reactance e) complex impedance
Modulation index is called elasticity of modulation when it is expressed as a percentage. True False
The modulated signal s(t)=[A1+A2cos(2лf1t)]сos (2лf2t) was generated by modulating a sinusoidal carrier with single tone message signal. If A1 is 3 Volts and A2 is 8 Volts, then the power in the modulated carrier is a. 12.500 Watts Ob. 32.000 Watts O c.0 Watts d. 60.500 Watts O e. 4.5000 Watts