A trunk is cut and held by a tree feller as shown. If the hydraulic cylinder AC in this position is known to experience a compressive force of 283.46 kN, determine the corresponding (a) weight of the trunk, and (b the pin reactions at B. All dimensions are in cm. Solution with incorrect FBD will not be considered. Also all required forces should be reported in kN. 230 A 205 B 20 75 110 FIO All dimensions are in cm.

A trunk is cut and held by a tree feller as shown. If the hydraulic cylinder AC in this position is known to experience a compressive force of 283.46 kN, determine the corresponding (a) weight of the trunk, and (b the pin reactions at B. All dimensions are in cm. Solution with incorrect FBD will not be considered. Also all required forces should be reported in kN. 230 A 205 B 20 75 110 FIO All dimensions are in cm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the position shown for the log hoist, booms ACDF and EFG are perpendicular and EFG is parallel to AB. What is the maximum weight (in Ib) of the log if hydraulic cylinders BC and support a maximum of 4123 Ib and 9123 Ib, respectively? Note that BC is a duplicate cylinder. (Hint: Recall multiple failure criteria.) E DE can 12' 10 This is nor your own propèrty so do ngi uwe at n ghi way as if it were your own. Legend: '- foot “- inch A 45° B This is not were your e ownprop 12" o do not use it in way as 12" 24"
ses This course DIOCKS Members AC and AB support the 300-Ib crate. Determine the tensile force developed in member (AB). 3 ft 4 ft 4 ft Select one: a. F(AB) = 181.827 lb O b. F(AB) = 214 lb O c. F(AB) = 114 lb O d. F(AB) = 282 lb 17:29 AN
For the dam shown, determine the factor of safety against sliding and overturning. Use unit weight of concrete = 24 kN/m3 and coefficient of friction = 0.80. Show a complete solution
Question 16 10 20 kN 20 kN 20 kN 3m -40 kN 3m D. 3 m 40 kN- 3 m 6 m Determine the force in member CE. If the force is in compression, write your answer as negative. If the force is in tension, just input the value
A puck weighs 8 lb and rests on the center of the frictionless surface of the ramp supported in equilibrium by ropes AC and BC. Determine the normal force the ramp exerts on the puck as well as the tension in each of the two ropes. g Variable Value Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. a b C d e f g9 36.0 in 45.0 in 13.5 in 27.7 in 45.0 in 18.0 in 35.0 in B The normal force acting on the puck is pounds The tension in rope AC is The tension in rope BC is C pounds pounds
Determine the angle that will yield a maximum force uh member BC, along with magnitude and nature of this force. Note: use method of sections and show solution. Answer should be 45° & BCmax = 168 kN
SEATWORK: 20 KN/m Rah Rav 1. Solve for the reactions. 9m 60 KN/m Rb
A weight Wis dropped from a heighth on the mid-span at C of a simply-supported beam as shown, where the spring always remains vertical and is at its natural length when the beam is horizontal. For W-90 lb and the stiffness of the spring k-313 lb/in, determine the static elongation of the spring (apring). Le., h-0. [in] W 40" h 1"I
Current Attempt in Progress Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground at point B. The combined weight of the wheelbarrow and its load is 236 lb with center of gravity at G. 21" 18" Answer: P = i B 20" eTextbook and Media lb Save for Later Heing multiple attempt will impact your score 17" Attempts: 0 of 3 used Submit Answer
Required Information The elevation and tit angle of table AB are controlled by an operator's hand at point D. The table supports a box weighing 8.8 Ib with center of gravity at point G. The force applied by the operator is horizonta 18 in. Gil 30 A5 30 10 in. -12 in.- Determine the force the operator must apply to keep the table in equilibrium, and determine the force supported by all members of the machine. The force the operator must apply to keep the table in equilibrium and the force supported by each member of the machine are as follows: TAE lb By Ib By= Ib D= lb
Required information In the given figure, all pulleys are frictionless. Take the value of P to be 220 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. P 0.5 ft P0.58 --20-20-20- Determine the reactions at point A and the force supported by the cable. (Do not include a minus sign in your response.) The horizontal component of the reaction force at A is lb →. The vertical component of the reaction force at A is The tension in the cable is lb. lb 1.
ASAP