A two-tank liquid level system where liquid enters the first tank at the rate of qi and then flows to the second tank at the rate of q1 through an orifice of radius R1. Water then leaves the second tank at the rate of qo through an orifice of radius R2. Derive the state space model for the system. qi h₁ A₁, g, P R₁ h₂ A₂, 8, P R₂ %

A two-tank liquid level system where liquid enters the first tank at the rate of qi and then flows to the second tank at the rate of q1 through an orifice of radius R1. Water then leaves the second tank at the rate of qo through an orifice of radius R2. Derive the state space model for the system. qi h₁ A₁, g, P R₁ h₂ A₂, 8, P R₂ %

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q 6(a) Find the linearized incremental state-variable model for the system shown in Figure 8. Use the linearized pump relationship Wp = Wp - (P₂ - P₁) Note that w(t) Pa C₁ P₁ Wo Wp P2 - Pa Figure 8 Pa C₂ P2 R Wor Pa
In the two-pipe system, water flows continuously from the inner pipe and air from the outer pipe (steady-state). ˙The pressure change in both pipes is negligible. In addition, heat interaction with the environment, kinetic and potential energy changes are also neglected. In this system shown in Figure 1, the water flowing from the inlet number 1 is in the state of saturated vapor (gas). In this case, calculate the outlet temperature (T2) for the given system, using the ideal gas approximation for air. (it should be solved iteratively.) (Please solve it on paper and solve it line by line. When you type it, it becomes too complicated to understand. Also please explain your solution and don't write too close. Thank you for your effort)
In the two-pipe system, water flows continuously from the inner pipe and air from the outer pipe (steady-state). ˙The pressure change in both pipes is negligible. In addition, heat interaction with the environment, kinetic and potential energy changes are also neglected. In this system shown in Figure 1, the water flowing from the inlet number 1 is in the state of saturated vapor (gas). In this case, calculate the outlet temperature (T2) for the given system, using the ideal gas approximation for air. (Hint: it will be solved iteratively.)
Q2] A tank having cross sectional area of 0.2 m² is operating at steady state with an inlet flowrate of 1*10² m²/s, the flow-head characteristics are given by: 9. = 0.003 h + 0.0006 Where, q. = outlet flowrate, m?/s and h = tank level, m. a. Determine the transfer function relating inlet flowrate and liquid level with numerical values of the time constant and steady state gain. b. If the inlet flowrate increased from 1*10-3 m?/s to 1.1*10-3 m²/s for 200 s and then return to initial steady state value (pluse function). Find the level after 100 s and 300 s. Plot the response.
QUESTION 3Discuss the five characteristics of a System.
(1) For the hydraulic system shown (a) develop a model that represents the (1) (2) (3) system. (b) Represent the model in state space form
identify the differential equations defining the motion of the masses from the figure, via Newton’s 2nd law, hence construct the system matrix, A, where the state vector is:x=[x;x ̇;y;y ̇ ]
(b) A system of mass rotation rod has been run at 40 rad/s as shown in Figure Q1. The system has the following data, Mass Mass A Mass B Mass C (ii) Weigh 1.2 kg 1.8 kg Mc Radius 1.135 m 0.822 m Re Angle 113.4° 48.8° вс # Distinguish the relationship between mass, radius and angle for counterweight mass system.
use a quality of 0.01 for the initial state.
Question 3. Consider a mass-spring translational mechanical system in series. The spring has a nonlinear characteristics such that the relationship between the spring force and the spring displacement can be described mathematically f.(t) = 3x. Assume that the applied force is f(t) = 6+ 8f (t), where 8f(t) is a small force about the 6 Newton constant value. Assuming the output to be the displacement of the mass, obtain the state space representation of the system about the equilibrium displacement.
2. A rigid tank (volume = V) containing an ideal gas is initially at T, and P. At time zero, an exit pipe (area = A) is opened and gas flows out of the tank at velocity v = K(P – Pam)2, where P is the pressure in the tank, Patm is the pressure of the atmosphere outside the tank, and K is a constant. The temperature of the gas in the tank is maintained at T, during the process. The pressure and the temperature of the gas exiting the tank are Patm and T1, respectively. Assume that, inside the tank, the pressure and specific volume do not vary with position. %3D A. Derive a differential equation for the tank pressure P as a function of time t. B. Determine the time required for the tank pressure to reach Patm:
3. Dynamics and control of two tank in series The following system is given: A water storage Tank 1 in which water is stored at atmospheric pressure and distributed by gravity flow in a downfeed in the same type water storage Tank 2. Where: h1, h2 is water level(m), S1, S2 is squared area of botom of the tank cilinders (m²),F1 in/F2in-water inflow, F1/F2out- water outflow(m³/h), k1, k: Valve constant (m²5/h), pipe length is 2.5 ommited. F1in h1 S1 Tank 1 k1 h2 F1 out F2 in S2 k2 F2 out Tank 2 3.1 Describe the dynamic behavior of a tank 1 in terms of ordinary differential equations. 3.2 Describe the dynamic behavior of the level h2/ tank 2/, due to the input flow Flin. in terms of ordinary differential equations. 3.3 Determine the transfer function of the level h2 as output, due to the input flow Flin. 3.4 Select the strategy to control the plant / level control system / with Flin as control action and output- level h2/ tank 2 / Design the proper instrumentation and Sketch the P&ID…