Answered: A uniform shaft of diameter 30 mm is…

A uniform shaft of diameter 30 mm is subject to a 60 N of tangential force. Calculate the shear stress induced in the shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Related questions

Q: A hollow aluminum propeller shaft, 30 ft. long with 15 in. outer diameter and an inner diameter…

Q: Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to…

A: GivenT=800 Nmd=50mm=0.05 mFormulaσT=16Tπd3

Q: A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torque…

A: Answer: The torque transmitted by the hollow shaft is 4500 N•m.

Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…

A: Given: Power transmitted by the shaft P=75kWSpeed of the shaft N=200rpmModulus of rigidity…

Q: solid circular shaft rotates at 200 rpm and transmits power of 112 kW. Calculate the minimum…

A: Given, Rotational speed of shaft = N = 200 rpm Power transmitted = P = 112 kW = 112,000 W Allowable…

Q: The figure shows an inboard engine, 8-ft long steel drive shaft, and propeller for a motor boat. The…

A: Given data: P=200 hpN=3500 rpmG=12×106 psiτ=12000 psi Need to determine the diameter of the smallest…

Q: A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at…

Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

Q: Compute the torsional shear stress that would be produced in a solid circular shaft having a…

Q: A shaft 100mm in diameter and 3 m long, with built-in ends, is subjected to a clockwise torque of 4…

Q: 1. Calculate what horsepower a solid steel shaft 6 inches in diameter can transmit at 160 rpm if the…

Q: Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the…

A: Given, diameter of the wrench , d=2×0.4 cm=0.8 cm=8 mm Length, L=200 mm Allowable shear stress,…

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: Calculate diameter of shaft using maximum shear stress theory,when equivalent torque of 800 x 103…

A: Given data: The allowable shear stress for the shaft is τ = 80 MPa. The equivalent torque is T =…

Q: Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a…

Q: A hollow shaft is subjected to a torque of 40 kN-m and a bending moment of 60 kN-m. Equivalent…

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

Q: A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in…

Q: A steel shaft 50 mm diameter and 500 mm long is subjected to a twisting moment of 1100 N-m, the…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. If the…

Q: A solid steel shaft is to transmit 120hp. The allowable shear stress is 8,000 psi. Calculate the…

A: Given The solid steel shaft transmit power of P=120 hp. The allowable shear stress is τ=8000 psi…

Q: 8.2 (A). Calculate the dimensions of a hollow steel shaft which is required to transmit 750 kW at a…

Q: A hollow steel propeller shaft, 20 ft. long with 15 in outer diameter and 12 in. inner diameter,…

Q: A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

Q: A 4-spline shaft and to slide when not under load has a diameter of 2.5 in. Find the compressive and…

A: Givend=2.5inP=2500lbsL=2in

Q: A shaft of diameter 40 mm is subjected to 360 N-m torque. The length of the shaft is 10 cm.…

A: Given data: The diameter of the shaft, d = 40 mm. The torque subjected to the shaft, T = 360 N-m.…

Q: A hollow shaft has an inner diameter of 0.035 m and an outer diameter of 0.06 m. Compute for the…

Q: A hollow vertical cylindrical steel pipe with an outside diameter of 300 mm and 6 mm thick has a…

Q: Compute the torsional shear stress and the angle of twist in degrees in an aluminum tube, 600 mm…

Q: A shaft of 30 kW 710 r.p.m motor is 40 mm in diameter and is supported in bearings 500 mm apart.…

A: Given: The power of shaft is P=30 kW The revolution of shaft per minute is N=710 rpm The diameter…

Q: a) Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected…

Q: A square steel bar, 25 mm on a side and 650 mm long, is subjected to a torque of 230 N #m. Compute…

Q: A solid and a hollow shaft are made of same material. The diameter of the solid shaft is 300 mm and…

Q: A motor driving a solid circular steel shaftwith diameter d = 1.5 in. transmits 50 hp to a gear atB.…

A: Consider a shaft having radius R is subjected to a twisting moment T. Then, shear stress developed…

Q: A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in…

Q: A Wind Turbine has a maximum output of 2MW at a speed of 20 rpm. A shaft of length 2m made of EN8…

A: Given: Maximum power=2×106W Speed=20rpm or 2.094rad/s Design stress=240MPa Length of the shaft=2m…

Q: A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm.…

Q: A torque of Tx=200Nm and a torque of Mz=260Nm are applied to the stepped shaft in the figure.…

A: Given data as per question Tx=200Nm Torque Mz=260Nm Larger diameter =400 mm Smaller diameter=150 mm…

Q: A shaft drives a gear set that is transmitting 5 hp at 1750 rpm. The diameter of the shaft is 0.75…

Q: Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m…

Q: 5. A propeller solid shaft of a ship with 200 mm diameter transmit a power of 5 MW at 500 r.p.m. It…

A: The diameter of solid shaft, The power of solid shaft, The speed of solid shaft, Now, the power…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Data given- d = 100 mm T = 10 × 103 N-m = 10 × 106 N- mm Axial stress = 50 MPa

Q: A hollow steel propeller shaft, 18 ft long with 14-in. outer diameter and 10-in. inner diameter,…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A uniform shaft of diameter 30 mm is subject to a 60 N of tangential force. Calculate the shear stress induced in the shaft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A solid shaft 100 mm in diameter is subjected to an axial compressive load of 600 kN simultaneously with a torque that twists the shaft thru an angle of 1.5 degrees in the length of 8 meters. If G=80Gpa, compute the maximum normal stress in the shaft. This is a COMBINED STRESS problem. Please include drawings of the circle.
Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.
Compute the torsional shear stress in a hollow shaft with an outside diameter of 40 mm and an inside diameter of 30 mm when transmitting 28 kilowatts(kW) of power at a speed of 45 rad/s.
A shaft used in an aircraft engine is 50 mm diameter, the maximum allowable shear stress is 84 MN/m². Find the torsional strength of the shaft. If the shaft now has a hole bored in it, find the percentage reductions in strength and mass. a. If the hole is 40 mm diameter b. If the hole is 25 mm diameter.
A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20 mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 MPa.
A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the diameter of the shaft is 1.5 inches diameter the maximum torque T if a 1in, diameter hole is bored through the shaft? Sketch the shear stress distribution along a trial line in each case.
Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.