a water spider of mass m is resting on the surface of the water. Assuming that each leg supports one-eighth of its weight, what is the radius of depressure generated by each leg? Consider an angle of 30°

a water spider of mass m is resting on the surface of the water. Assuming that each leg supports one-eighth of its weight, what is the radius of depressure generated by each leg? Consider an angle of 30°

Name: a water spider of mass m is resting on the surface of the water. Assum
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: a water spider of mass m is resting on the surface of the water. Assuming that each leg supports one-eighth of its weight, what is the radius of depressure generated by each leg? Consider an angle of 30°.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.100P: The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
A concrete seawater dam is shown in cross section. Is the dam safe against tipping about edge A? The mass densities are 24000kg/m3 for concrete and 1030kg/m3 for seawater.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
The thin-walled cylindrical can with a spherical dimple weighs 0.2 lb. Determine the force P required to push the can into water to a depth of 8 in. Use =0.036lb/in.3 for water.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
Each of the three gates has a constant width 1: (perpendicular to the paper). Calculate the force P required to maintain each gate in the position shown. Express your answers in terms of b, c, h, and (the weight density of the fluid).
The cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.
The 20-ft-long gate of Fig. Is a quarter circle 6 ft and is hinged at H. Determine the horizontal force, P, required to hold the gate in place. Neglect friction at the hinge and the weight of the gate. Water Gate Hinge
A float sensor for the determination of the level of water in a vessel has a cylindrical float of mass 2.0 kg, cross-sectional area 20 cm2 and a length of 1.5 m. It floats vertically in the water and presses upwards against a beam attached to its upward end. What will be the minimum and maximum upthrust forces exerted by the float on the beam? Suggest a means by which the deformation of the beam under the action of the upthrust force could be monitored.
What is the net force on a ball of mass 20kg and volume of 0.3 m3 when it is submerged under water?
A bucket hangs off the end of a rod rigidly attached to a pulley. A spring acts as a counterbalance. The spring has a spring constant of 250 N/m. The bucket has a mass of 2 kg. When the angle a is 0°, the spring is unstretched. What is the volume of water (in liters) that must be put in the bucket in order to for the rod AB to be horizontal? What are the reactions at pin A in that case? Note that the density of water is 1000 kg/m³. B. .75 m .3 m A
A float sensor for the determination of the level of water in a vessel has a cylindrical float of mass 2.0 kg, cross-sectional area 20 cm= and a length of 1 5 in. It floats vertically in the water and presses upwards against a beam attached to its upward end. What will be the minimum and maximum up thrust forces exerted by the float on the beam? Suggest a means by which the deformation of the beam under the action of the force could be monitored