Air enters an adiabatic nozzle at 230 kPa, 600°C with a velocity of 60 m/s. The air is at70 kPa, 450°C at the exit of the nozzle. Model the air as an ideal gas having variablespecific heat, using values from Cengel's tables posted on Canvas.a) Find the exit velocity of the air (answer: 577.1 m/s).b) Find the isentropic efficiency of the nozzle (answer: 0.643).

A nozzle is a smooth-varying cross-sectional channel that converts working fluid pressure energy…

Answered: Air enters an adiabatic nozzle at 230…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5) Explain the "burst potatoes in the boiling water" with thermodynamic viewpoint.
Po Q7) A piston/cylinder arrangement, contains air at 250 kPa, 300°C. The 50-kg piston has a diameter of 0.1 m and initially pushes against the stops. The atmosphere is at 100 kPa and 20°C. The cylinder now cools as heat is transferred to the ambient. Alr 25 cm a. At what temperature does the piston begin to move down? b. How far has the piston dropped when the temperature reaches ambient?
Air Initially at 14.7 psia and 80 deg. F is heated in a constant volume non-flow process until the temperature reaches 1500 deg. F. The air is then expanded isentropically until the original volume is tripled. Using air tables, Find a) the heat added at constant volume, Btu/lb and b) the work done, Btu/lb
2) Water vapor enters a continuous flow adiabatic turbine at 15 MPa pressure, 500 °C temperature and 90 m/s velocity, and exits at 20 kPa pressure, 92% dryness and 80 m/s speed. Since the mass flow rate of the steam is 43.2 tons/h, a) The power produced in the turbine (in MW, HP, ton.km/h), b) Find the turbine inlet and outlet cross-sectional areas (in m2, cm2).
1.Acertain ideal gas has a constant R= 0.21kj/kg.k with k=1.4. Find a) Cp, Cv b) If 1.5 kg of this gas undergoes a reversible nonflow constant volume process from Pı=138 kpaa, and T1=60°C to 392°C,find AU,AH,Q,W, c) For steady flow process AP=0,AK=0, find W and AS.
Air at 30°C Dry-bulb temperature, 40% RH enters a heating chamber at the rate of 500 cmh (cu.m/hr). The air undergoes constant temperature heating and leaves the chamber with an RH of 70%. (a.) At standard atmospheric condition, find the heat added (in kW) and the amount water added (in kg/ min).
If 6 liters of air at a pressure of 100 kPaa and 25 0 C are compressed reversiblyaccording to PV 2 = C, until the volume becomes 2 liters. Please answer the following a. The thermodynamic process the problem representsb. the pressure, temperature, and volume after the processc. change in internal energy, change in enthalpy and change in entropyd. work nonflow and heat transferred
In a constant pressure process, 325 KJ of heat are added to 6.55 kg of ideal gas(R=208 J/kg-K and k = 1.65) initially at 290 K. Calculate:a. Final Temperatureb. Change in enthalpyc. Change in internal energyd. Change in entropye. Non-flow work
Steam expands in a steam turbine steadily at a rate of 32,000 kg/h, that enters the turbineat 7 MPa and 600 oC (look to the Fig. 1); whereas, it leaves the turbine at 25 kPa as saturated vapor. Ifthis turbine generates a power of 6.5 MW at the ambient conditions of T0=27 oC, then,a) Write the mass balance of the fluid entering and leaving this turbine.b) Obtain the energy balance to determine the heat loss of the steam turbine,c) Find the entropy generation using the entropy balance and determine the destroyed exergy using thegenerated entropy,d) Find the exergy destruction using the exergy balance ,e) Find the maximum possible power output,f) Determine the second-law efficiency (ηII) of the steam turbine,
This is an Isothermal Compression of Ammonia [not an ideal gas] Ammonia in a piston-cylinder device initially at 700kPa, 303K undergoes a reversible isothermal compression process until the volume is reduced to 25% of the initial volume. a) Draw the process T-s and p-v-diagrams, relative to saturation lines. b) What is the heat and work per unit mass?
Ex/ a cylinder is closed by piston and inside it gas has mass (0.45 kg) and pressure (6.7 bar) and temperature (185 °C). The gas is expanded by adiabatic process and becomes has new pressure (138 kpa) and temperature decreased by values (165 K). the work done by the piston is (53 kJ) calculate (Cv) and (y).
Q5/ Air expands at constant pressure from 100 KPa, 0.03 m3 to 0.06 m3 with 80 kJ negative heat transfer. There is no work other than that done on a piston. Find total energy difference for the air. *

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS