:An open belt drive with (200 and 150 mm) pulleys diameters, and the central distance equal to (0.5 m). The larger pulley speed is (500 r.p.m.), and the coefficient of friction between the belt and the pulley is (0.35). Calculate the power transmitted by the belt drive when the maximum tension on the belt equal to (2200 N).

:An open belt drive with (200 and 150 mm) pulleys diameters, and the central distance equal to (0.5 m). The larger pulley speed is (500 r.p.m.), and the coefficient of friction between the belt and the pulley is (0.35). Calculate the power transmitted by the belt drive when the maximum tension on the belt equal to (2200 N).

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.70P: Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at...

See similar textbooks

Similar questions

A double-ply leather belt transmits 10 hp from a motor with a pulley 8-in. in diameter, running at 1700 rom, to a 24-in. diameter pulley. The difference in tension may be taken as 20 lb/in. of belt width. Belt thickness is 0.2. Calculate the required width of belt
(b) The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in Figure Q2 (b). The motor exerts a torque of 7 Nm to drive the system. The coefficient of static friction for both pulley is 0.35 and both pulleys has an equivalent diameter. Calculate the tension of T;and T, of V-belt just before it start rotating. M A B Øg= 120 mm Ø= 120 mm Figure Q2 (b)
Find the power transmitted by a belt running over a pulley of 600 mm diameter at 200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, angle of lap 160° and maximum tension in the belt is 2500 N.
In a belt arrangement two pulleys are connected by flat belts having same diameters. Themaximum force on the tight side of belt is 662 N. If co-efficient of friction is 0.3 thenwhat is maximum force on the slack side of the belts?
Find the power transmitted by a belt running over a pulley of 600 mm diameter at200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25,angle of lap 160° and maximum tension in the belt is 2500 N.
Q2 A flat belt type is used for a belt drive system connecting two pulleys 1.2m apart. The driver pulley with diameter 40 cm is rotating with the speed 350 rpm, while diameter of driven pulley is 100 cm. Coefficient of friction of the contact surface between belt and pulley is 0.3. Maximum allowable tension is 600N. (i) Find the power transmitted by the belt, P. (ii) Determine the Initial tension of the belt, TA. (iii) If the flat belt is now replaced by a Vee-belt with groove angle of B = 30°, find the power transmitted by this belt. Give explanation why power transmitted by flat and Vee-belt type are not the same. Explain your answer according to basic friction concept.
3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5° and angle of contact of belt with the pulley is 160°. If the mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power. Consider the centrifugal tension in the belt.
(b) The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in Figure Q2 (b). The motor exerts a torque of 7 Nm to drive the system. The coefficient of static friction for both pulley is 0.35 and both pulleys has an equivalent diameter. Calculate the tension of T, and T, of V-belt just before it start rotating. M A B 120 mm 120 mm Figure Q2 (b)
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included angle of 40°, and density 1400kg/m 3 The angle of lap is 130° on the smaller wheel, the coefficient of friction is 0.4 and the maximum force allowed in the belt is 500N. Calculate the initial belt tension and reason for this.
Q2 / A belt drive consist of two V-belts in parallei, on grooved pulleys of the same size. The angle of the groove is 30". The cross - section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximum safe stress in the material is 7 MN/m. Answer the following questions 1- The centrifugal tension in belts is . . (a) increases power transmitted (b) decreases power transmitted (e) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
Q1: A simple flat belt drive system shown in the figure has a driving pulley diameter 220mm and runs at 800 r.p.m. clockwise; the diameter of driven pulley is 360mm. The contact angle is 210°. The belt wide is 20mm and 8mm thick. The belt mass per unit length is 0.5 kg/m and the maximum stress in the belt is 8 MN/m. If the coefficient of friction between the belt and pulley is 0.25; take the centrifugal force in to account and determine: 1. Redraw the figure and show (The Tight and Slack sides, tension and centrifugal forces directions at this two sides and the contact angles) 2. The speed of the belt on the driving pulley 3. The tension forces on the belt in the Tight and Slack sides 4. Power transmitted in the system 5. The generated Torque in the dri ing pulley Driven Pulley Driving Pulley