·An Sl engine is modelled with an Otto cycle and operated at part throttle. The air-fue with AF = 15 enters the cylinders at 75 kPa and 58°C. The compression ratio r. = 9.5:1, the exhaust pressure constant volume specific heat c, = 0.821 kJ/kg-K, the specific heat ratio k = 1.35, the gas constant of air R = 0.287 kJ/kg-K, and combustion efficiency n. assumed that there is no exhaust residual. Calculate the temperature in cylinder at start of combustion [°C] (Express your answer as an integer). = 100 kPa, the heating value Qay = 43,000 kJ/kg, the %3D 96%. It can be

·An Sl engine is modelled with an Otto cycle and operated at part throttle. The air-fue with AF = 15 enters the cylinders at 75 kPa and 58°C. The compression ratio r. = 9.5:1, the exhaust pressure constant volume specific heat c, = 0.821 kJ/kg-K, the specific heat ratio k = 1.35, the gas constant of air R = 0.287 kJ/kg-K, and combustion efficiency n. assumed that there is no exhaust residual. Calculate the temperature in cylinder at start of combustion [°C] (Express your answer as an integer). = 100 kPa, the heating value Qay = 43,000 kJ/kg, the %3D 96%. It can be

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW Find the Volumetric efficiency
Question 3 A four-cylinder of 1.6 liters S.I engine (S4PH with BSFC = 0.5 lb/HP- hour) has the specification as follows: ü Injector size = 240 c.c/min with the fuel pressure set at 43.5 p.s.i ü I.D.C = 80% at W.O.T Calculate: i. Current S4PH engine horse power ii. The new injector flow rate, if we raise the fuel pressure at 50 p.s.i [lb/hour] iii. The new fuel system's horse power capacity iv. The % HP enhancement
1- A four-cylinder, two stroke cycle diesel engine with (10.9 cm) bore and (12.6 cm) stroke produces (88 kW) of brake power at (2000 RPM). Compression ratio is (18:1). Determine: (a) Engine displacement. Ans.: (4700.6 cm³). (b) Brake mean effective pressure. Ans.: (561.7 kPa).
2. Which of the following equations describes the chocked nozzle thrust in a gas turbine engine? O FN=(co-co). Wa FN = (C9 - Co). Wa + (p9 - Po).A9 W. = Wair+Wfuel - Wbleed gas hc = cp.(CPR(1-1/)-1)/hic Wa.hc = (Wa+W+).ht.nm Dikdörtgen Biçin
5. How many times the intake valve opens in a 4-stroke-cycle engine running at 2000 rpm. 6. If the compression ratio is 1:17, the clearance volume for 100 cm3 piston displacement volume is ___. 7. If a 4-cylinder, 2-stroke-cycle internal combustion engine has 600 explosion per minute, what is the engine rpm?
In a 4 stroke single cylinder engine clearance volume (Vc) is 30 cm3 and displacement volume (Vd) is 290 cm3. The piston bore is 60 mm. Intake valve is opened at an angle of 25 ᵒ CA before Top Dead Center (TDC) and is closed at an angle of 20 ᵒ CA after the Bottom Dead Center (BDC). Calculate effective compression ratio.
An 8-cylinder, 4-stroke diesel engine has power output of 368 low at 800 rpm. The fuel consumption is 0.238 kg/kwh. The pressure in the cylinder at the beginning of injectionis 35 bar and max. pressure is 60 bar. The injector is adjusted at 210 bar and max. pressure at in the injector is 600 bar. Calculate orificarea required per injector if the injection takes place over 12° of crank rotation assume Cd = 0.6. p,=0.85.
An automobile carburettor having its flost chamber vented to the atmosphere is tested. at sea level conditions in the factory without air cleaner. The main metering system of this carburettor is found to yield a fuel-air ratio of 0.065. The venturi throat pressure is 0.85 bar. The carburettor is now installed in an automobile and air cleaner is placed on the inlet to carburettor. The air flow rate with or without air filter is 230 kg/hr. The pressure drop through the filter is found to be 0.035 bar at sea level conditions. vesuming 7 and orifice coefficient to be constant calculate: The ventues throat pressure with air cleaner. (n) Air-fuel ratio with air cleaner.
PARTS A & B ( Read and Solve carefully) At the beginning of the compression process of an ideal Diesel cycle operating with the compression ratio r = 18.1, the temperature is T1 = 300K and the pressure is P1 = 0.1MPa. The temperature at the end of the combustion process (the highest temperature of the cycle) is T3 = 1800 K. Evaluate the cutoff ratio rc and the heat delivered during the combustion process qin (in kJ per kg of air) using PART (A) - air standard (variable specific heat) PART ( B) - cold-air standard (constant specific heat evaluated at room temperature). which result, (a) or (b), more accurately represents the actual process in a diesel engine??
Briefly explain the determination of gas pressure excitations in a 4-stroke engine.
You have been asked to help with the low-pressure compressor (LPC) design for a turbofan engine with a bypass ratio of 8.4. The preliminary cycle design calls for the LPC to produce a pressure ratio of 9.4 with the following operating conditions and constraints. .Inlet Conditions TO2 Poz Core Air Mass Flowrate (kg/s) (K) (kPa) 282 24.6 47.0 Design Constraints Maximum Polytropic Efficiency 94.1% Maximum Stage Pr 1.55 Estimate the minimum number of stages required for this LPC. Then assuming the 1st stage of the LPC operates at the maximum allowable pressure ratio, determine the stagnation temperature exiting the 1st stage, and the stage's adiabatic efficiency. Also determine the power (W) required to operate the full LPC (not just 1st stage). Finally, what would be the percent change in the required power if the polytropic efficiency was only 90.0%.
Q4) Choose the true answer of the following questions : (1) The engine speed is measured using....... (a) viscous-flow air meter. (b) dynamometer (b) air box method (d) tachometer (2) The crank shaft is connected to the piston by....... (a) fuel injector (b) connected rod (c) camshaft (d) valves (3) The brake power is (a) less than indicated power (b) more than indicated power (c). eqaul to the indicated power (4) Two-stroke engines have (a) valves (b). ports instead of valves (c). none of them (5) ....... is a mechanical device used to cool a gas after compression. (a) cylinder (b). supercharger (c) intercoole (d) dynamometer