Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4350 mm² and an allowable normal stress of 85MPa. Bar (2) has a cross-sectional area of A₂ = 4550 mm² and an allowable normal stress of 80 MPa. Assume x₁ = 1.5 m, x₂ = 3.0 m, y₁ =1.4 m, and y₂ = 2.5 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowablenormal stress.Y₁AAnswer: Pmax=(1)BPx₂KN

Answered: Image /qna-images/answer/937b1040-12a8-4e66-8f4c-4a0053fe1fcf.jpg

Answered: Answer: Pmax= i kN

Engineering

Mechanical Engineering

Answer: Pmax= i kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.10P: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in...

See similar textbooks

Related questions

Q: A 2 4 M F B L₂ L Y C 4 Pipe ABC is supported by three smooth journal bearings, Find the reactions at…

A: Applied force F = 480 lbsApplied moment M = 180 lb-ftAngle of the applied force , θ = 45°Lengths: L1…

Q: Beam loading: 0.4 m R₁ 800 N 12 mm Beam cross-section: 30 mm 0.9 m 0.8 m- A 400 N 600 N +0.3 B…

Q: Question 3 (a) With the aid of diagram, differentiate between heat transfer mechanisms of conduction…

A: Difference between conduction and convection

Q: Air at 15°C and 100 kPa occupies 0.03 m³. The air is heated at constant volume until the pressure is…

Q: For the clevis connection shown, determine the shear stress in the 20-mm-diameter bolt for an…

A: the clevis connection shown,To Find-The shear stress in the d= 20mm diameter bolt for an applied…

Q: The speed of a car increases uniformly with time from 38 km/h at A to 91 km/h at B during 16…

A: Speed of a car increases uniformlySpeed at A = 38 km/h VA = 38 × 5/18 = 10.55556 m/sSpeed at B = 91…

Q: The system is at rest with the spring unstretched when 8 = 0. The 5.3-kg uniform slender bar is then…

A: mass,m=5.3 kgb=0.45 mto determine:(a) Spring constant k(b)magnitude of angular velocity

Q: Fundamental Problem 4.7 Figure 1 -1m- F3 of 1 2 m- 45° 2.5 m F F₂ Part A Determine the resultant…

Q: 1 kg of a gas at a temperature of 40° C and a pressure of 120 KPa occupies a volume of 0.25m3. If…

Q: *6-56. Water flows through A at 6 m/s and is discharged into the atmosphere at B and C. Determine…

A: It is given that the velocity at A , diameter at A is , diameter and . It is required to determine…

Q: 1) Determine if pump pressure is sufficient to lift the weight L: 3 Li 1.4m C 4m 5 6kg oc Dynam 32sm…

Q: 100 mm T=? 45° 300 mm 400 mm O 250 mm The mechanism shown in the figure is in static equilibrium.…

A: In the above diagram, is angle of BC with horizontal and is angle of CD with horizontal.

Q: The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is…

Q: L. 4 (in circle) 5 (in circle) 6 (in circle) 7 (in circle) 8 (in circle) 1(not in circle) 4(not in…

A: to match the following numbers with correct terminology1 (in circle): 2 (in circle):3 (in circle):4…

Q: The temperature at the beginning of a compression process of an air standard Otto cycle with a…

A: Draw the p-v diagram for Otto cycle.Given, Compression ratio, a) For process 1-2 Isentropic…

Q: What are the key factors to consider when designing a Distributed Control System (DCS) for a…

A: Distributed Control System (DCS) is a specialized system used in manufacturing or processing…

Q: Problem 1: Determine the force in each member. State if the members are in tension and in…

Q: The velocity of a particle moving in the x-y plane is given by (5.92i + 4.07j) m/s at time t = 5.92…

A: Given:The velocity of a particle is at .The acceleration of a particle is at .Formula used:The…

Q: The 9 lb particle is subjected to the action of its weight and forces F₁ = {2i+ 6j - 2tk} lb, F₂ =…

Q: Blocks A and B each require 30-N cable tension to start them sliding (Figure P4-44). Deter- mine…

A: The tension in the cables connecting blocks A and B, T = 30NTo find:The force P and the angle .

Q: Determine the minimum coefficient of static

A: Given Data The mass of the car m= 1400 kg=1400*9.81=13734NFind Outa) The minimum coefficient of…

Q: The truss is subjected to a vertical force of magnitude 500 N at joint D. The system is supported C…

Q: Consider the system shown in (Figure 1). Figure 1 of 1 Part A Determine the moment of the force F…

A: Given F=80 lb Positions of the points. Required: Moment of the force about A.

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: n this question, you will calculate the second moment of area for a 4 ✕ 6 piece of lumber about the…

A: Let Ixx be the second moment of the area about the x-x axis.Let Iyy be the second moment of the area…

Q: 2 m A B F 2 KN C E 3 kN 2 kN D The truss shown consists of three sections 3.6 m wide and 3 m tall,…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: Determine the value of item (k)

A: Given: Arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear ATo do:To…

Q: What are the key factors that influence the convective heat transfer coefficient in a mechanical…

A: Convective heat transfer, a mode of thermal energy transport, occurs due to the bulk motion of…

Q: a=(3.7m) , b=(3.7m) ,theta =(33) , p1=(3.7)KN , p2=(2.4)KN find the forces in each members…

A: According to the given dataWe need to findforce in each member.

Q: 2) A steady, incompressible, two-dimensional velocity field is given by V(u, v) = (2+2.5x + y)i +…

Q: Determine the ongular accelerations of the bors, if the system is released from the figure shown.…

A: Given:To find:Angular velocity of the bars

Q: Calculate the magnitude of the resultant force on the indicated area and its location NOTE: THE GATE…

A: Given:The specific weight of the Oil is .The diameter is .Consider free body diagram:

Q: Determine the velocity of the point D at this instant.

A: Given DataThe disk velocity at point A vA=4.9 ft/sThe disk velocity at point B vB=9.8 ft/sThe radius…

Q: Beam cross-section: 12 mm 30 mm Determine the Maximum Shear Stress in the beam. A/

Q: Problem 3. Outcome 5. Please show all work. Air at standard pressure but with T = 50°C flows through…

Q: Determine the distance the ball is from the origin 3 s after being released from rest. Express your…

Q: A Christmas decoration is suspended by two wires. Two equal tension forces in the wires each act at…

Q: Air flows over a stationary flat plate at speed of 4,5 m/s . Plate has a width of 1 m. Air has a…

Q: The 100 kg cylinder has an angular velocity of 30 rad/s If the coefficient of kinetic friction is…

A: Mass of cylinder,m=100 kgangular velocity,Coefficient of kinetic friction,Kc=0.2Radius of…

Q: What is the underlying mechanism for the observed deviation from ideality in non-ideal solutions,…

A: This question is based on the thermodynamic properties.

Q: Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A.…

A: Given:The gear A rotates clockwise CW.Gear B and C are on the same shaft and gear D and E are on…

Q: The driver of the truck has an acceleration of 0.34g as the truck passes over the top A of the hump…

A: Given Data

Q: The velocity for the 2-dimensional flow is defined by V =(3y2 i+4xj) m/s, where y is in meters.…

A: Given data is

Q: Determine the distance the ball is from the origin 3 s after being released from rest.

A: Given Data The mass of the particle The ball is initially at restFind OutThe distance of the ball…

Q: What are the factors that influence the buckling behavior of an axially loaded slender column in…

A: Buckling is a sudden, unstable deformation of a structure, often leading to its failure. It…

Q: .a) Explain the purpose of the brake assist system and the traction control system. b) Explain how…

A: Brake Assist System (BAS):The purpose of the Brake Assist System is to enhance braking performance…

Q: The cover of a cylindrical pressure vessel made of cast iron is shown in fig.1 The inner diameter of…

A: Given:The inner diameter of the cylinder is .The internal pressure is limited to .The number of…

Q: Question #1: Determine the shear, axial, and bending moment distributions for the loaded beam shown…

A: Calculate and plot shear axial and bending moment distributions

Q: om the given figure shown below, determine the centroidal moment of Inertia (Ixo and lyo) of the…

A: From the figure, we can conclude that all the values are in inches.

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4350 mm² and an allowable normal stress of 85
MPa. Bar (2) has a cross-sectional area of A₂ = 4550 mm² and an allowable normal stress of 80 MPa. Assume x₁ = 1.5 m, x₂ = 3.0 m, y₁ =
1.4 m, and y₂ = 2.5 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable
normal stress.
Y₁
A
Answer: Pmax=
(1)
B
P
x₂
KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Calculation of angles

VIEW

Step 2: Calculation of maximum value of force P

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
An aluminum bar subjected to tensile Forces P has a length L = 150 in. and cross-sectional area A = 2.0 in2 The stress-strain behavior of the aluminum may be represented approximately by the bilinear stress-strain diagram shown in the figure. Calculate the elongation S of the bar for each of the following axial loads: p = 8 kips, 16 kips. 24 kips, 32 kips, and 40 kips. From these results, plot a diagram of load P versus elongation S (load-displacement diagram).
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A circular aluminum tube of length L = 600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d2= 75 mm and d1= 63 mm, respectively. A strain gage is placed on the outside of the lube to measure normal strains in the longitudinal direction. Assume that E = 73 GPa and Poissons ratio is v = 0.33. (a) IF the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e = 78 J X 10-6, what is the shortening
A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A copper bar AB with a length 25 in. and diameter 2 in. is placed in position at room temperature with a gap of 0.008 in. between end A and a rigid restraint (see figure). The bar is supported at end B by an elastic spring with a spring constant k= 1.2 × 106 lb/in. (a) Calculate the axial compressive stress crcin the bar if the temperature of the bar only rises 50 F. (For copper, use a = 9.6 × 10-6/ and E = 16 × 106 psi.) (b) What is the force in the spring? (Neglect gravity effects.) (c) Repeat part (a) if k ? 8.