Assume all the processes to be reversible and the heat losses from the pump and the turbine to be negligible. (a) If steam enters a pump (operates between the pressure limits of 5 MPa and 10 kPa) as saturated liquid, determine the pump work (consumed) per unit mass. (b) If steam leaves a turbine (operates between the pressure limits of 5 MPa and 10 kPa) as saturated vapor, determine the turbine work (delivered) per unit mass.

Assume all the processes to be reversible and the heat losses from the pump and the turbine to be negligible. (a) If steam enters a pump (operates between the pressure limits of 5 MPa and 10 kPa) as saturated liquid, determine the pump work (consumed) per unit mass. (b) If steam leaves a turbine (operates between the pressure limits of 5 MPa and 10 kPa) as saturated vapor, determine the turbine work (delivered) per unit mass.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine designed for an output of 100 MW receives superheated steam with the following conditions; h = 3550 kJ/kg, v1 = 40 m/s, h2 = 1356 kJ/kg, v2= 125 m/s. Assume no heat loss, determine the desired mass flow rate of the steam (kg/s).
Air goes through a Brayton cycle gas turbine, entering the compressor at 11 °C and 108 kPa. When it reaches the turbine inlet, the air is at 1,061 °C and 1.23 MPa. What is the net change in specific enthalpy of the working fluid after going through the compressor and heat addition processes? You may assume that the specific heat capacity c, is a constant 1.005 --1. kJ-kg 1.K1 throughout the whole cycle. Give your answer in kJ-kg1 to one decimal place.
4. Steam enters the condenser of a steam power plant at 20000 kPa and a quality of 95 percent with a mass flow rate of 20 Mg/h. It is to be cooled by water from a nearby river in circulating the water through the tubes within the condenser. To prevent thermal pollution, the river water is not allowed to experience a temperature rise above 10oC. If the steam is to leave the condenser as saturated liquid at 20000 Pa, determine the mass flow rate of the cooling water required
A 12" x 14" horizontal single-acting reciprocating air compressor is driven by a 50 kW motor that operates at 520 rpm, drawing in air at 14 psia and 88 F, and discharging it at 57.6 psia. The compression and re-expansion process are polytropic with n = 1.33. Mechanical efficiency = 85 %, compression efficiency = 75% Calculate: a). the mass of air (lb/min) discharged b). volumetric efficiency (%) c). the percent clearance (%)
The relation of pressure to volume for a closed system undergoing a cyclic reversible process is shown in the figure below. Calculate the net work for the cycle.
Refrigerant flows through a water-cooled condenser at a rate of 25 kg/ min. The specific enthalpy of refrigerant entering the condenser is 400 kJ/kg, and leaving, is 220 kJ / kg. Determine the mass flow of cooling water through the condenser for a temperature increase of the water of I 0° C, assuming no external heat exchanges.
A turbine receives steam at the following state: pressure 1200 kPag, enthalpy 2875 kJ/kg, speed 33.3 m/s and elevation 30 m. The steam leaves the turbine at the following state; pressure 20 kPag, enthalpy 2152 kJ/kg, speed 100 m/s and elevation 0 m. Heat is lost to the surroundings at the rate of 29 kJ/s. if the rate of steam flow through the turbine is 0.24 kg/s, what is the power output of the turbine in kW? Assume steady flow conditions.
a) The entropy change of the refrigerant is kJ/K . (b) The entropy change of the source is kJ/K . (c) The total entropy change during the process is
1. Steam is supplied to a fully loaded 100 hp turbine at 200 psia with u, = 1160 BTU/lb, v, = 2.6 ft/lb and v1 = 380 ft/s. Exhaust is at 1.1 psia with uz = 900 BTU lb., v2 = 1200 ft/s. The heat loss from the steam in the turbine is 10.5 BTU.lb. Neglect the potential energy change and determine: a. the work per Ib steam b. the steam flow rate in Ib/hour 2. An ideal gas (R = 2,075 J/kg K and k = 1.659) goes through a reversible constant pressure process where 525 kJ o heat are added to 2.3 kg of the gas. The initial temperature of the gas is 310 K. Compute for the following: a. final temperature, T2 b. non-flow work Wn c. change in entropy AS d. flow work Assume AP = AK = 0) 3. A 3.6 kg. mass of air goes through an isothermal process with a temperature of 305 OK. The initial and final pressure of the air are 550 kPa and 135 kPa respectively. Compute for: a. steady flow work, Wf b. non-flow work Wn c. change in internal energy AU d. Heat transferred, Q e. change in entropy, AS
Refrigerant 134a enters a refrigerator compressor as superheated vapor at 0.20 MPa and -5 ° C at a rate of 0.7 kg / s, and exits at 1.2 MPa and 70 ° C. The refrigerant is cooled in the condenser to 44 ° C and 1.15 MPa, and is throttled to 0.2 MPa. Neglecting any heat transfer and any pressure drop in the connecting lines between the components, show the cycle on a Ts and Ph diagram with respect to the saturation lines, and determine (a) the rate of heat removal from the refrigerated space and the power input to the compressor, b) the isentropic efficiency of the compressor, and c) the COP of the refrigerator
Energy Balance in an Open System Compressed liquid water with an enthalpy of 100.0 kJ/kg entered a boiler which maintains the pressure and temperature at 2500 kPa and 500 °C respectively. Upon leaving the boiler, the superheated steam entered a turbine where it exited at a temperature of 45 °C and enthalpy of 2000 kJ/kg. The mass flow rate is 1000 kg/s. (A) Determine the heat added to the boiler in Watts in order to turn the compressed liquid water into superheated steam. (B) Determine the work output of the turbine in Watts. (C) Indicate the condition of the fluid exiting the turbine if it is saturated and the quality.
A feed water heater is used to preheat water before it enters a boiler, as shown schematicallyin Figure Q1. A mass flux of 30 kg/s flows through the system and, 7 kg/s is withdrawnfrom the turbine for the feed water heater. Neglecting losses through the various pipes andcomponents determine(a) the feed water heater outlet temperature,(b) the boiler heat transfer rate,(c) the turbine power output,(d) the total pump power required,(e) the energy rejected by the condenser,(f) the cooling water mass flux, and(g) the thermal efficiency of the cycle.