Assume that the exclusive-OR gate has a contamination delay of 3 ns and that the AND or OR gates have a contamination delay of 2 ns What is the total contamination delay time in the 4-bit adder? Note: your answer should include only the value of the delay without the unit (only the number) Note: Submit your work on paper as well А- В- Cin- Cout Answer:

Assume that the exclusive-OR gate has a contamination delay of 3 ns and that the AND or OR gates have a contamination delay of 2 ns What is the total contamination delay time in the 4-bit adder? Note: your answer should include only the value of the delay without the unit (only the number) Note: Submit your work on paper as well А- В- Cin- Cout Answer:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume that the exclusive-OR gate has a contamination delay of 10 ns and that the AND or OR gates have a contamination delay of 5 ns. What is the total contamination delay time in the 8-bit adder? Note: your answer should include only the value of the delay without the unit (only the number) A B- Cin- Cout Answer:
Question 3:a) We can construct the full adder/Sub tractor with the help of AND-OR gate and also by using exclusive OR Gate. What is the between these two circuits?b) Construct the circuit of multiplexer which can multiply more than two bits.
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…
Draw logic diagram for half adder and full adder circuit using Logisim Software
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Q2/Find the addition result for the following operation (66)8+ (1100)EX-3+(83)10-(F2.1)16 using 2's complement, assume that the result is binary number * 10011111.1111 None of them O 110000010.111 1111101.0001 O 1100000.0001
Below is a 4-bit up-counter. What is the largest number of the counter if the initial state Q 3 Q 2 Q1Q0 =0011? (D 3 an Q 3 are MSB, and when Load = 1 and Count =1 the counter is loaded with the value D 3 ...D0) 4-bit counter Clock Q3 Load Count "I" or Vcc "I" or Vcc Do "1" or Vcc - D, Qi Q2 "0" or Gnd - D2 "0" or Gnd D3 Q3 1111 0011 1100 0110
For a Core2 descriptor that contains a base address of 00333000H, a limit of 0000166AH, and Granularity bit =1. What starting and ending locations are addressed by this descriptor?
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
A figure of a simple 1 bit ALU with multiplexer Cin BO AO „Cout MIMO Full Adder 4:1 Mux FC Logical Unit a. How many AND gate and OR gate to construct this circuit ? b. Suppose you want to add a "subtraction function" in this ALU circuit. How do you modify this circuit ? Draw the revised circuit.
Binary 4-bit Asynchronous down Counter and explain how it functions, find real life applications
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, The logic "0" will be applied to the burned parts. Draw this circuit.