attempt- 1883268cmid-4951 Google O UVLė: Log in to the. table 4. Which of the following shows an appropriate diagram of the tension forces acting on the ring such that it is possible for the resultant to be a zero vector? Note that the value of G is not equal to H. Hint: The eraser does not slide if the resultant of the frictional force and normal force is vertical. A. B. H. H. D. H. 5. Which of the following best approximates the value of the angle h (in degrees) if G = 100 N and H = 75 N?

attempt- 1883268cmid-4951 Google O UVLė: Log in to the. table 4. Which of the following shows an appropriate diagram of the tension forces acting on the ring such that it is possible for the resultant to be a zero vector? Note that the value of G is not equal to H. Hint: The eraser does not slide if the resultant of the frictional force and normal force is vertical. A. B. H. H. D. H. 5. Which of the following best approximates the value of the angle h (in degrees) if G = 100 N and H = 75 N?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The punch and die arrangement shown is used to punch out thin plate objects of different shapes. The cross-section of the punch and die shown is a circle of 1-in. diameter. A force P=6 kips is applied to the punch. If the plate thickness t - in., determine the shearing stress in the 8 plate. Punch TF Plate Die Die 6.
A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P end B as shown in figure. The wire is made of high- strength steel having modulus of elasticity E= 210 GPa. The diameter of the wire is 5mm. Determine the maximum load P that could be applied so that the vetical displacemt at B will not be more than 6 mm?
D A 150 mm E B -150 mm -2 mm (a) Al-76 mm--76 mm- 75 mm The plate shown in the figure is a fixed connected along AB and held in the horizontal guides at its top and bottom, AD and BC. If its right side CD is given a uniform horizontal displacement of 2 mm, determine (a) the average normal strain along the diagonal AC, and (b) the shear strain at E relative to the x, y axes. 75 mm В (b)
W A Test beam A Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 b Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm B = 41 mm t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
Problem 2. The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. Determine the length L that results in portion BCD of the wire being horizontal. B 150 mm 200 mm D
A beam having a tee-shaped cross section is subjected to equal (12 kN.m) bending moments, as shown in Figure. The centroid location (y-) is (110 mm) measured upward from bottom edge of stem, the moment of inertia about the z axis, is (Iz 18646000 mm4).Determine the maximum bending stress produced in the cross section. State whether the normal stress is tension (T) or compression * .(C) 100 mm 25 mm 12 kN-m 175 mm 150 mm 12 kN-m 25 mm 70.8 MPa (T) O 75.8 MPа (С С 45.0 MPa (T) O 30.8 МPа (С) О
A force-couple system is acting on the frame as shown. Use A=80N, B=700N, C=150N, and M= 120N.m. The system is to be replaced with a single resultant force R. B 30° [Select] [Select] [Select] [Select] [Select] [Select] M 400 mm 200 mm 300 mm (a) Calculate the absolute value of the x-component of the resultant in N. (b) Calculate the absolute value of the y-component of the resultant in N. (c) Calculate the magnitude of resultant in N. (d) Calculate the angle that the resultant makes with the horizontal in degrees. (e) Calculate the absolute value of the x-intercept of the resultant's line of action in mm. (f) Calculate the absolute value of the y-intercept of the resultant's line of action in mm.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 512 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 643 mm2. For the 32 kN force shown, determine the deflection of D (mm) *Note: Negative if compression and positive if tension. Also, the final answer should have two decimal places.
W A L A Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. b Section A-A Strain gauge 1 Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a D Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm • B = 41 mm • t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
The two bars are made of polystyrene, which has the stress-strain diagram shown. If the cross-sectional area of bar AB is 975 mm² and BC is 2600 mm², determine the largest force P that can be supported before any member ruptures. Assume that buckling does not occur. Include complete steps with explanations and FBD. 1m baxilno σ (MPa) 175 140 105 70 A 35ptension 0 0.20 -1.2 m P 0.40 compression B 0.60 0.80 € (mm/mm)
50 MPа A 35 MPa B 30 90 MPa The state of stress at a point in a member is shown on the element. You are required to determine the normal stress and shear stress acting on the inclined plane AB and show the result on the sectioned element: Using the method of equilibrium, and NOTE: support your answer with sketches and the FBD.