B 2. A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has seven rungs and the rungs are spaced 0.30 m apart, and the top and bottom rungs are 0.30 m from their respective ends of the ladder. Surfaces at A and B both have the same coefficient of friction. If a worker weighs 630 N and stands on the middle rung, determine the minimum value of the coefficient of friction so that the ladder does not slide. Neglect the weight of the ladder. 10=60° A

B 2. A 2.4 m ladder rests on a vertical wall as shown in the figure. The ladder has seven rungs and the rungs are spaced 0.30 m apart, and the top and bottom rungs are 0.30 m from their respective ends of the ladder. Surfaces at A and B both have the same coefficient of friction. If a worker weighs 630 N and stands on the middle rung, determine the minimum value of the coefficient of friction so that the ladder does not slide. Neglect the weight of the ladder. 10=60° A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 3000 lb weight is raised by two 70 wedges as shown. f for all contact surfaces is 0.23. Determine the minimum force P.
4. A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping.
N and is considered to be concentrated at G. The ladder also supports a vertical load of 150 at C. Compute the least value of (a) at which the ladder maybe placed without slipping to the left. 1m 4 m G 150 N 30 N A ladder 5 meters long rests on a horizontal ground and leans against a smooth vertical wall at an angle 70° with the horizontal. The weight of the ladder is 900 N and acts at its middle. The ladder is at the point of sliding, when a man weighing 750 N stands on a rung 1.5 m from the bottom of the ladder. Calculate the coefficient of friction between the ladder and the floor.
CDEFGH is plate with a circular hole in it and has a unit weight p (N/m2). It is attached on DE beam with weld. A crate has a weight of W (kN) at A is linked to the plate from C by the help of a cord. The surface under the crate has a coefficient of static friction µ, and the pulley has a coeficient of static friction µ2. a) Find the center of the gravity of the CDEFGH plate according to O (given in grey color in the figure). HCD is half circle centered at O. • A full circle centered at O is removed from the plate. • HOD line and EF line are vertical. b) What should be the minimum weight of the box at A in order to prevent the movement of the plate to downward. c) What are the support reactions at K. Note: P=400 B 0.3 A H G Hi 3m Co 3m F Im 20° D E K 4m 6m
A mechanism carries a constant load P applied to the seat as shown. For the angle 8, determine the following (a) the lengths LBE and LAB, in m (b) the angles a and p, in degrees Draw the complete FBD of (c) members AB, FG, EBH and GHI 6 Calculate the forces, in Newtons, for the following (d) member FG (e) pin H (f) hydraulic cylinder AB Given: P = 770 N, 0 = 30.4° E 100 175 Jos ou si ION 400 LBE This is not yoproperty so do not u in any way of 150 0 C SV ANG FUD UJ operty so do not if it were you 150 D E 175 B 200 Dimensions in millimeters G H 150 This is not your property so do not use it in any way as if it were your
5. A 390-kg block is resting on a 29 deg inclined plane with a coefficient of friction = 0.63. Find the required horizontal force P (kN) that is necessary to start the block UP the incline. ROUND OFF TO TWO DECIMAL PLACES.
Find the tengion for AB, AC that honging rope and A D box weight in balance shown in Fig a 300 N. The values are as follow s 1.8 m. 3.6 m. 2.4 m. 2.5 m. 1. 4 m . %3D f 1. 0 m. Q ves tion F (AB) = FCAC) = FCAD) :
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
A uniform 80.0 N ladder 4.0 m long is placed against a frictionless wall with its base situated 2.0 m from the wall. Find the forces exerted by the wall and by the ground on the ladder.
N and is considered to be concentrated at G. The ladder also supports a vertical load of 150 at C. Compute the least value of (a) at which the ladder maybe placed without slipping to the left. 1m 4 m G 150 N 30 N 2. Aladder 5 meters long rests on a horizontal ground and leans against a smooth vertical wall at an angle 70° with the horizontal. The weight of the ladder is 900 N and acts at its middle. The ladder is at the point of sliding, when a man weighing 750 N stands on a rung 1.5 m from the bottom of the ladder. Calculate the coefficient of friction between the ladder and the floor.
7. A ladder of length 12 m leaning up against a wall makes a 50 degree angle with the ground. The top of the ladder has sliders so that it can slide up and down the wall. Therefore, consider the top of the ladder to be frictionless. The ladder has a weight of 189 N that acts at its center. Someone weighing Fg = 1000 N is 0.92 m vertically below B, but on the ladder. Another person is on the ground holding the ladder by pushing on it horizontally with a force F. If the coefficient of static friction is 0.32, find the horizontal force F that must be applied at a vertical height of 1.2 m to prevent the ladder from slipping. LL F 1.2 m 12 m 50⁰ Fg B .92 m
1. A hydraulic press has a ram of 30 cm diameter and a plunger of 4.5 cm diameter. Find the weight lifted by the hydraulic press when the force applied at the plunger is 500 N.