(b) A transfer function of the digital antenna system, H(z) can be represented in the ratio of z-transform of the output signal,Y(z) to the z-transform of the input signal, X(2). Let say the input signal is in unit step function and output signal can be represented as y[n] = 6(8[n]) + (3") [Satu rangkap pindah bagi sistem antena, H(z) boleh di wakilkan sebagai nisbah isyarat keluaran transformasi-z,Y(z) kepada nisbah isyarat masukkan transformasi-z, X(z). Andaikan isyarat bagi masukkan adalah fungsi unit langkah dan isyarat keluaran boleh di wakilkan sebagai yln] = 6(8[n]) + (3")/ (i) Solve the z-transform of the input and output. [Selesaikan transformasi-z bagi masukkan dan keluaran.]

(b) A transfer function of the digital antenna system, H(z) can be represented in the ratio of z-transform of the output signal,Y(z) to the z-transform of the input signal, X(2). Let say the input signal is in unit step function and output signal can be represented as y[n] = 6(8[n]) + (3") [Satu rangkap pindah bagi sistem antena, H(z) boleh di wakilkan sebagai nisbah isyarat keluaran transformasi-z,Y(z) kepada nisbah isyarat masukkan transformasi-z, X(z). Andaikan isyarat bagi masukkan adalah fungsi unit langkah dan isyarat keluaran boleh di wakilkan sebagai yln] = 6(8[n]) + (3")/ (i) Solve the z-transform of the input and output. [Selesaikan transformasi-z bagi masukkan dan keluaran.]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q: Compute the Z-transform of the signal ??[?].
Given the matrices:a. Find the transfer function in direct form.b. Represent the system by signal flow graph and indicate the variables in it.c. Draw a corresponding block diagram
Prepare and fill in the karnaugh map of the bole algebra function in the picture (do not reduce).
Ramp unit r(t) signal is: a. Periodic O b. Discrete c. Non periodic O d. Insufficient information
b. Impulse sampling of continuous time signals. What happens in time domain and frequency domain when we sample a signal. How sampling frequency is determined?
Through the final reduced expression (of the image ). Apply the input signal below and show how the output behaves
please quickly thanks ! true or false 5 The signal to noise ratio is 3dB, it means the signal power is double than the noise power
A=4 , B=7, c=2 xCt) = b+a. Coslat+ ) -at h4)=2.e .u(t) %3D Calculate the output signal? (give as equation)
Frequency spectrum of a signal is given as the following: a) Write an equation for the signal x(t) defined by this frequency spectrum. b) What is the minimum sampling frequency to sample this signal? c) Write x[n] after the signal digitized by an ADC with a sampling frequency of 2 Hz.
TRA Ans: 385 For Pinite support signal x [n] =n[n](w[] _ 4[n-11] where r[w] is the discrete time. -? ramp fonction, the energy of xin]
If there is a signal m(t) = 5sin2000πt + cos4000πt + 2.5cos3000πt will be changedinto a digital signal with the ADC device.a. Determine the minimum sampling frequency according to the Nyquist condition!b. What is the distance between samples in ms?
2. For the signal above, convert it into its digital representation using the sampled points. You need to think about the number of bits you would represent each sample as. This is referred to as Quantisation. Example, if you need 8 different levels of sound, then 3 bits are sufficient (23 = 8). 04 0.3 02 0.1 -0.1 -02 -0.3 -04 0.5 1 1.5 2.5 3 3.5 4 4.5 5 55 6 6.5 7.5 8 8.5 9.5 10 What is the sampling rate in this case??