b) The following figure shows a sampled signal and the desiredsampled signal. A digital signal processing system isrequired to change the sampled signal to produce thedesired output signal.1Desired output-1 0 1 2 3 45Sampled signal-0.4 -0.3i) Design the required digital signal processing system andprovide the z-transfer function. Determine and commenton the system's stability.

Answered: Image /qna-images/answer/5c1e3a73-6a14-4764-a686-7bcae4bf1e93.jpg

b) The following figure shows a sampled signal and the desired sampled signal. A digital signal processing system is required to change the sampled signal to produce the desired output signal. Desired output -4 -3 -2 -10 1 2 3 4 5 Sampled signal -0.4 -0.3 i) Design the required digital signal processing system and provide the z-transfer function. Determine and comment on the system's stability.

b) The following figure shows a sampled signal and the desired sampled signal. A digital signal processing system is required to change the sampled signal to produce the desired output signal. Desired output -4 -3 -2 -10 1 2 3 4 5 Sampled signal -0.4 -0.3 i) Design the required digital signal processing system and provide the z-transfer function. Determine and comment on the system's stability.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. Consider the electrical circuits shown in figure a.) and b.). For each circuit determine the transfer function C/2 C12 2R 2R (a) R (b)
This question from digital signal processing course.
4. Signal conditioning element basically takes the output of the sensing element and converts it into a form more suitable for further processing, usually in the form of a DC voltage, DC current or variable frequency AC voltage. The output of the sensing element is usually too small to operate an indicator or a recorder. Therefore, it is suitably processed and modified in the signal conditioning element so as to obtain the output in the desired form that is amplify the signal and filtering the unwanted signal. i. Describe the aliasing phenomenon. ii. Suggest a solution to minimize the effect of aliasing.
3. (a) The following figure depicts a sampled analog signal for digital signal representation. By applying the concept of Pulse Code Modulation, assume there will be 4-bit code words for each sampled amplitude. Calculate the normalized PAM value and normalized quantized value for the given analog signal value at different time stamps . Assume that the sampling amplitudes are between -32V to +32V. Time Analog Signal Value (V) -10.8 1 14.5 30.6 -21.7
b) Draw the block diagram of the phase - locked loop (PLL) that can be used to demodulate FM signals. Explain briefly . the operation of this demodulator
A sinusoidal signal of 2 kHz frequency is applied at the input of a delta modulator with a step size of 0.1 volt. The sampling rate of the delta modulator is 20000 samples per second. What will be the maximum amplitude of the sinusoidal signal if there is no slope overload distortion?
a. What is the condition for over modulation and what are its effects? b. Name the frequencies generated in the output of an Amplitude Modulator.
1)to VRMs value to generate a signal with a peak voltage of 10 V with a signal generator in a multisim program..................... must be entered. 2)) the frequency of the signal generator to produce a signal with a period of 10ms...................... must be entered as. What should come to the dotted line?
What is the condition for over modulation and what are its effects?
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Digital Electronics and Design Questiona) Write a 2:1 MUX module using Verilog-HDL.b) Use the module in (a) and write a Verilog-HDL code to implement a 4:1 MUX.
One way to control power, in an electronic system is to using the PWM (pulse width modulation) method. To create an adjustable signal pulse width, one of which is used a window comparator as shown in the figure (VCC = +12 V, VEE = -12 V). If a 10 Vpp 10 kHz signal is given as an input, determine the complete output waveform by displaying the reference voltage. (compare with the input)