Exercise A single span beam is simply supported between two columns and carries a reinforced concrete slab in addition to the column and loading shown below. Using the design load indicated, select a suitable section considering section dassification, shear and bending only. Assume S275 steel and that dead loads are inclusive of self-weights. 41.2 N 3.17 im 3 m 3 m Universal Beam Section

Exercise A single span beam is simply supported between two columns and carries a reinforced concrete slab in addition to the column and loading shown below. Using the design load indicated, select a suitable section considering section dassification, shear and bending only. Assume S275 steel and that dead loads are inclusive of self-weights. 41.2 N 3.17 im 3 m 3 m Universal Beam Section

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

Check the following reinforced concrete beams for bending. The beams are on a simple span of 26.5ft. They support uniformly distributed service loads of 3.20 kip/ft live and 1.80 kip/ft dead excluding beam weight. Assume the 28 day strength of the concrete is 3000 psi and the rebar is Grade 60. 5-#9 ㅏ 16' (a) 35' 38'
Exercise A single span beam is simply supported between two columns and carries a reinforced concrete slab in addition to the column and loading shown below. Using the design load indicated, select a suitable section considering section classification, shear and bending only. Assume S275 steel and that dead loads are inclusive of sell weights. 41.2 KN T 3.17 W/m 3m. 3 m Lnversa Beam Saction. an May 201 41 2へ ane home ins prt sc delete f12 f11 f10 fg num lock -> backspace 二D 8. } P.
Q2 1- Check the following weather one way or two way 2- Calculate the design ultimate load Wu on the on the beams B3, B6 Assume slab load: Live load = 5 kN/m2 Dead load = 8 kN/m? Beam size 300x500 mm %3D B5 B6 B7 3.6 m |L 4.8 4 m 5m 5m BI B2 B4
3. A beam has the following distributed loads : wD = 0.44 kip/ft, and wL 0.76 kips. If the beam is W 18 x 50, braced at the ends and third points, made from A992 steel, by directly applying the provisions of the AISC Specification, what is the available flexural strength of this beam? What is the adequacy of this beam in providing the required flexural strength. L 35'
Problem. A SRCB is subjected to loads as shown. Required: Adequacy of the SRCB against flexure @ midspan & support based on USD -NSCP 2010. Draw V & M diagram. Use: fy= 41A MPa; fc'=3C MPa; sc=70 mm. A=3mm, B=7mm, C=8mm, D=7mm. DL = 2A KN/m & LL=3B KN/m A=3 B=7 2m 6.D m C=8 D=7 1m 4-2Ammp 3C0 6B0 4-2Ammø REBARS SECTION OF SRCB (Units in mm)
4. An exterior column shown should be more of an axial member than a flexural member if the Demand-Capacity ratio for flexure does not exceed 80%. Determine the minimum value of axial compressive strength using LRFD to satisfy the said condition. The column is safe against sidesway. Express k in 2 significant figures. Data for materials are given below: 7.5 m Steel used: A-50 I for Column: 687 x 10 mm I for Beam: 485x 10° mm Column Area: 32300 mm? Column radius of Gyration= 146 mm 4 6.2 m %D
What is the ultimate uniaxial load capacity of the given column section, according to the design strengths of the materials? Concrete is C30, longitu- dinal steel bars and ties are B420C. Longitudinal bars are o14, ties are o10. b= 300 mm, h= 400mm. The column will be produced on site with adequate quality control. %3D h 1357 kN b) 750 kN 2490 kN d) 1150 kN 1470 kN Leave blank
4) Compute the shear force (VRDC) for the beam. Check if beam needs shear rebar. Given Cross Shear force obtained in critical section, VED-35 kN Assume 1.5 for K value Rebar: 4012 in tension Material properties: fck-25 MPa (concrete). fyk-420 MPa (steel) Effective height, d=560 mm Material reduction factors: 1.5 for concrete, 1.15 for steel section dimension: b-300 mm, h=600 mm section 000 Twitte
Note: please use Set B data thank you 2° M₂ A B * 4 m 2m The cantilever beam above is made up of concrete with E- 70 MPa, refer to the table below for the properties and loads for the beam: PROPERTIES LOADS SET b (mm) h (mm) w (kN/m) Mb (kN-m) A (1,3,5,7,9) 300 500 20 40 B (2,4,6,8,0) 250 400 15 45 Using area moment method, determine the following: Flexural rigidity of the beam in N-men²
Qualitative analysis of beam & frames of constant flexural rigidity – Plot BMDs on tension side
The beam given below is to be const ructed from C30 concrete with B420C st eel. Clear cover is 40 mm. According to the given shear and moment envelopes find the required amount of flexural and shear reinforcement along the beam. Only ø16 bars are available as longit udinal reinforcement and stirrups will be manufactured from ø12 bars. Draw the reinforcement det ails. A B 900mm K101 300 520 K102 300 520 Column Column Column 60cm 60cm 40cm 1300mm 7m 4.5m 160 150 2.5m 3.5m V (kN) 4m 70 2.5m 310 180 120 100 40 M (kNm) 70 130 120mm 400mm
3. Figure 3 shows partly of a simply supported beam supports uniformly distributed characteristic dead and imposed loads, qEd, of 5 kN/m each. Assume the steel grade is S275 and the UB size is 356 x 171 x 67 kg/m, determine the beam resistance capacity of (CLO2, PLO3) a) Transverse force (use loading type c) (PLO3, CLOS) b) Deflection (PLOS, CLO3) Flange width b, = 173.2 mm Web thickness = 9.1 mm h= 363.4 mm 356X171 X67 kg/m UB Flange thickness = 15.7 mm Stiff bearing length s, 100 mm Figure 3