c) Figure 6 is the waveform of output voltage, vo from synchronous connection changer. The primary voltage is 220 V (rms), 60 Hz. The secondary voltages are Vi = 120 V and V2 = 100 V. If the load resistance is R = 6 Q and the rms load voltage is 150 V with delay angle, a = 93°, determine the; i. rms current of thyristors T1 and T2. ii. rms current of thyristors T3 and T4. iii. input PF. V2(V1 + V2) of Figure 6

c) Figure 6 is the waveform of output voltage, vo from synchronous connection changer. The primary voltage is 220 V (rms), 60 Hz. The secondary voltages are Vi = 120 V and V2 = 100 V. If the load resistance is R = 6 Q and the rms load voltage is 150 V with delay angle, a = 93°, determine the; i. rms current of thyristors T1 and T2. ii. rms current of thyristors T3 and T4. iii. input PF. V2(V1 + V2) of Figure 6

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.3MCQ: The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of...

See similar textbooks

Similar questions

The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
An alternating current varying sinusoidally with a frequency of 50 Hz has anrms value of 20 A.a) Determine the instantaneous value at 0.0025 seconds.b) Determine the instantaneous value, 0.0125 seconds after passingthrough a positive maximum value.c) At what time, measured from a positive maximum value, will theinstantaneous current be 14.14 A?
In DC choppers the wave forms for input and output voltages are respectively a. both discontinuous b. discontinuous,continuous c. both continuous d. continuous,discontinuous
An ac voltage represents by a sinusoidal waveform as shown in Figure 6 below. a) Define: i. The period ii. The frequency
What is the average power in ghe single phase ac circuit with the purely resistive load? It is sinusoidal steady state excitation.
In non-sinusoidal wave sources, the dissipated power in the load is depends on the value of . . Variable Current Average Current Constant Current All-of-them
In capacitive AC circuit voltage is leading current O a. True O b. False
3-9 An rms ac voltmeter and a peak-to-peak-reading ac voltmeter are to be used to determine whether three ac signals are sinusoidal. Deter. mine whether the signals are sinusoidal if the following readings are obtained First signal Second signal Third signal peak-to-peak reading = 35.26 V rms reading. - 12.00 V peak-to-peak reading - 11.31 V rms reading = 4.00 V peak-to-peak reading = 25.00 V rms reading -8.83 V
Draw the full-wave voltage doubler circuit diagram. When a 1:4 transformer is used in this circuit andIf Vo=12sin(314t) alternative signal is obtained at the output, the frequency of the input signal, maximum and rmsCalculate its value.
Facts A clipper is a device that removes either the positive half (top half) or negative half (bottom half), or both positive and negative halves of the input AC signal. In other words, a clipper is a device that limits the positive amplitude or negative amplitude or both positive and negative amplitudes of the input AC signal. In some cases, a clipper removes a small portion of the positive half cycle or negative half cycle or both positive and negative half cycles. In the below circuit diagram, the positive half cycles are removed by using the series positive clipper. Question: In your own opinion. Why do we need to clip a certain amount of voltage in positive or negative or on both sides? What is the benefit of that in our devices or circuits in doing such thing?
Protection Schemes for Series Capacitor (compensation )
Generate a conclusion on this following statements: Determine and analyze the voltage regulation characteristics of the alternator with resistive, capacitive, and inductive loading.