Calculate the shearing force (kN, rounded off to the nearest whole number) needed for a blanking operation on a metal sheet with the following properties: UTS (MPa) Yield strength (MPa) Elongation (%) 880 1050 6 The shape of the blank is as shown, consisting of rectangular plate with a perforated center (perforation is also rectangular). The sheet metal has a thickness of 2.5 mm. The shearing force, Fshear, may be calculated from the equation: 3 mm 25 mm F₂ "shear = (0.7%) * T * L where ou is the ultimate tensile strength, T is the sheet thickness, and L is the total length of the sheared edge. a) 271 b) 221 c) 1378 d) 462 e) 323 45 mm 15 mm

Calculate the shearing force (kN, rounded off to the nearest whole number) needed for a blanking operation on a metal sheet with the following properties: UTS (MPa) Yield strength (MPa) Elongation (%) 880 1050 6 The shape of the blank is as shown, consisting of rectangular plate with a perforated center (perforation is also rectangular). The sheet metal has a thickness of 2.5 mm. The shearing force, Fshear, may be calculated from the equation: 3 mm 25 mm F₂ "shear = (0.7%) * T * L where ou is the ultimate tensile strength, T is the sheet thickness, and L is the total length of the sheared edge. a) 271 b) 221 c) 1378 d) 462 e) 323 45 mm 15 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

= If you have a rod with an initial diameter 12 mm, final diameter is 10 mm and yield stress 40Mpa, it drawn with a pulling force of 300N. Calculate the requisite drawing .stress 104.55Mpa. O 78.99Mpa. O 89.25Mpa. O
Choose the correct answer for the following: 1. In the bulk deformation process, there is a change in the thickness of the wokpiece. Thus, the ratio of the surface area to the volume is... c. small. a. equal. 2. In the metal forming process, if the temperature increases, the metal working becomes easier due to reducing in .. a. n and K. 3. The true tensile strain can be calculated from the following relation... B. very high. b. melting temperature. C. hardness a. e =In (1+e). b. e =In). C. e = In() e =In(; 4. In rolling operation, large diameter roll induces.. on the surface of the rolled part. b. tension stress. a. compression stress. c. no residual stress 5. the preheating treatment is not necessary if the carbon equivalent in the steel part is ... b. 0.6 a. 0.3 c. 0.8
An ASTM A228 music wire has the diameter of 0.038 in Part A Find the ultimate tensile strength. Express your answer in pounds per square inch to three significant figures. Part B Find the ultimate shear strength. Express your answer in pounds per square inch to three significant figures.
A drawing operation is performed on 3.0 mm stock. The part is a cylindrical cup with height H = 50 mm and inside diameter Dp = 70 mm. Find the required starting blank diameter Db. Do not find the blank diameter. My question is why is the formula for the volume of cup = pi*Dp*h*t + pi*Dp2*t / 4. Are u able to illustrate it in the picture as i had trouble visualizing it A picture of the cylindrical cup is given.
2) A 2 mm thick metal sheet is to be bent at an angle of one radian with a bend radius of 100 mm. If the stretch factor is 0.5, the bend allowance is 99 mm 100 mm 101 mm 102 mm
A 20 mm diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress is 80 Mpa, what tensile force applied each plate to shear the bolt?
Question 2) Forces of F; =8 kN in the z direction from the point B in the figure, F 2 =6 kN in the z direction from the point C, and F 3 = 10 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L 1 =0.17 m and L 2 =0.11 m. It is desired to determine the stress state of point A on the aa section taken from the arm. The radius r of the section is r=0.2 m and kThe shear modulus of the ol material is also G=80 Gpa . According to this; a L2 D L1 F2 F3 F1 B.
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 , write 120 DO NOT INCLUDE THE UNITS IN YOUR ANSWER. JUST ITS VALUE AND THE (-) SIGN IF APPLICABLE (ex: 10, 0.30, -3, -0.20) Include the negative sign if your flexural stress, shear stress, shear force, bending moment is negative. DO NOT leave a space between the negative sign and the value.
For the profile shown in fig.1, write the part program-using G-code programming where the work piece thickness is 20mm by using end mill Ø10mm. 190 100 RIS RIS RIS R1S R15
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…
A bending operation is to be performed on 5.00 mm thick cold-rolled steel. The part drawing is given in Figure below. Determine the blank size required. t5.00 58 40 R-8.5 46.5
3) Impact strength value increases with increase in cross-sectional area at notch. Select one: True False