Can someone show me the solution, please? 1. Determine the characteristic impedance for an RG-59A coaxial cable with the following specifications: L = 0.118 μH/ft and C = 21 pF/ft. Answer: Z0 = Ω 2. Calculate the characteristic impedance if an open-wire transmission line consisting of two wires with diameter 1 mm and separation 1cm. Answer: Z0 = 359 Ω

Can someone show me the solution, please? 1. Determine the characteristic impedance for an RG-59A coaxial cable with the following specifications: L = 0.118 μH/ft and C = 21 pF/ft. Answer: Z0 = Ω 2. Calculate the characteristic impedance if an open-wire transmission line consisting of two wires with diameter 1 mm and separation 1cm. Answer: Z0 = 359 Ω

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.17P: Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All...

See similar textbooks

Similar questions

A- Define Impedence. Mention the difference between Impedence and Resistance ? B- A coaxial cable's shiled diameter is 0.4cm and the inner conductor has a diameter of 0.02cm. What is the characteristic impedance of that cable? C- What is meant by impedance matching? Why is impedance matching is needed?
An over head transmission line supported from two towers location at the same level. The distance between the towers is 200 m. The tension in the wires is 9000 N. The weight of one meter of the conductor is 10 N. The sag of the wires is * 2.55 m 1.55 m 4.55 m 5.55 m Non of them
Assume that a single-conductor belted cable has a conductor diameterof 0.681 in., inside diameter of sheath of 1.7025 in., and a length of8000 ft. The cable is to be operated at 12.47 kV. The dielectricconstant is 4.5, and the power factor of the dielectric at a ratedfrequency and temperature is 0.05. Calculate the following:(a) Capacitance of cable.(b) Charging current.(c) Dielectric loss of cable.(d) Equivalent resistance of insulation.
A two-wire DC splitter of 1Km length and resistance of each conductor (m/00030.0) and feeds the loads as shown in the augmented form: 1. Minimum voltage point on the conductor 2. The voltage at each load point 400V 200m 300m 400m 100m 80A 60A 10A SOA
A three phase, 11 KV, underground cable system, consider a single core of conductor radius 0.5 cm diameter and lead sheath of 1.25 cm. The core and lead sheath have been separated by two intersheaths with radius 0.75 cm and 1 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same.
Write any four methods of voltage control and Draw the basic block diagram of AC – DC transmission system. and A transmission line has a span of length 250 m and the weight of the conductor per metrelength is 0.63 Kg. The tension in the conductor is 1250 Kg. Calculate the sag and heightabove the ground at which the conductor should be supported. Consider the groundclearance required is 13m
a) Explain the demerits of non-uniform potential gradient of insulated cable. b) 'Insulation resistance varies proportionally with the value of insulation thickness - justify this statement with appropriate equations. c) A single core cable to be used on a 50kV single phase system. Maximum permissible dielectric is not to exceed 35kV/cm (peak). I. Determine the most economic conductor and cable diameter. II. Estimate voltages on the inter sheaths, if two inter sheaths are introduced to increase 32% of the existing working voltage of the cable using the method of 'inter sheath grading
A three phase, 33 KV, underground cable system, consider a single core of conductor radius 0.8 cm diameter and lead sheath of 2.3 cm. The core and lead sheath have been separated by two intersheaths with radius 1.3 cm and 1.8 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same. Please i need it know please
Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All strands have the same radius r.
An over head transmission line supported from two towers. The high of the two towers are 30 m and 20 m respectively. The distance between the towers is 300 m. The tension in the wires is 7000 N. The weight of one meter of the conductor is 12 N. The horizontal distance between the long tower and point o (minimum center middle point)
In an AC LVDT system, measuring the output voltage alone gives an indication of the displacement from the center, but not the direction of displacement. Explain why, and also explain a method for solving this problem.
The capacitance of a single phase two-wire transmission line depends on: Select one: a. All the above O b. the material of cables c. the radius of cables d. the distance between the cables O e. None of above