parallel circuit consists of two branches connected to a 120 V, 60 Hz source. The first branch has a noninductive resistance load of 50 Ω. The second branch consists of a coil with an inductance of 0.2 H and negligible resistance. Find the current in each branch. Determine the line current. Determine the power factor of the parallel

parallel circuit consists of two branches connected to a 120 V, 60 Hz source. The first branch has a noninductive resistance load of 50 Ω. The second branch consists of a coil with an inductance of 0.2 H and negligible resistance. Find the current in each branch. Determine the line current. Determine the power factor of the parallel

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18MCQ

See similar textbooks

Similar questions

a capacitor and a resistor are connected in parellel to a 120 v 60 hz line the resistor has a resistance of 40 ohms and the capacitor has a capacitance of 132.6 uf what is the total current flow through the circuit. what is the impedence and the power factor and how many degrees out of phase are the current and voltage out phase with eachother.
A 206.0-2 resistor and a 2.80-µF capacitor are connected in series across the terminals of a sinusoidal emf with a frequency of 150 Hz. The inductance of the circuit is negligible. What is the impedance of the circuit?
Value of series impedance if inductance is 5mH , resistance is 4 ohm and frequency is 50 Hz.
An electrical engineer is working with a parallel AC circuit. The circuit draws 8 ohms on a resistive branch, and the angle of the total impedance is 35°. What is the approximate number of ohms on the inductive branch? O 0.7 O 4.59 O 5.6 O 6.55
A resistor of 150 ohms, a coil with reactance 100 ohms and a capacitor with reactance 200 ohms are connected in series. What is the complex impedance R + jX?
A coil and a capacitor are connected in series. The inductive reactance is 250 ohms, and the capacitive is reactance is -300 ohms. What is the net impedence vector, R + jX?
4. Design the network in the figure to have the following characteristics: i. BW - 500 Hz ii. Qp = 30 iii. Vemax = 1.8 V 0.2 mA Z0° C7 R, = 0 N
An inductive circuit has a resistance of 10 ohms and an inductance of 2 henrys. The total impedance at 60 HZ is?
A parallel circuit has 10 ohms of resistance and a capacitive reactance of 15 ohms, An ac rms voltage of 200 V isapplied across it. What is the magnitude of the total current?
A 47-ohms load resistor is connected in series with a 10-uF capacitor. At what frequency will the capacitor reach the same value as the load resistor?
The attached image shows a circuit with an AC voltage source, a resistor, inductor, and capacitor connected in series. The circuit has the following characteristics: Resistor resistance: 10 ohm Capacitor capacitance: 0.05 F Inductor inductance: 13 H Current Amplitude: 4 A Voltage amplitude across the source: 60 V Frequency at the source: 0.3 Hz Voltage amplitude across the resistor: 35 V Voltage amplitude across the capacitor: 37 V Voltage amplitude across the inductor: 80 V (a) Calculate the RMS voltages from the amplitudes above. From the RMS voltages across the capacitor, inductor and resistor, calculate the RMS voltage of the AC source. Hint: Vrms = V0/sqrt(2) Vrms = sqrt( (Vrms,R)2 + (Vrms, L - Vrms, C)2 ) (b) Calculate the RMS value of the current (c) Using the resistance, capacitance, inductance, and the frequency of the AC voltage, calculate the impedance Z. From this, and the previously measured value of Vrms, find the RMS value of the current in the circuit.
True power can be determined by measuring voltage and current in a. R-L series circuit b. Purely resistive ac circuit c. Purely capacitive circuit d. Purely inductive circuit