● Compute the time needed for the cylinder position to retract from the maximum position 1m to minimum position Om, given that the big chamber is full of oil at the beginning when the position is at the maximum position. The valve is working in position2. Cylinder piston and rod diameters are 80 mm and 40 mm, respectively. Diameter Dv of the turbulent orifice is 2 mm, the discharge coefficient Cd is 0.6 and oil density is 860kg/m^3. The mass on the piston rod is m = 5000 kg. Transmission line losses and compressibility are neglected.

● Compute the time needed for the cylinder position to retract from the maximum position 1m to minimum position Om, given that the big chamber is full of oil at the beginning when the position is at the maximum position. The valve is working in position2. Cylinder piston and rod diameters are 80 mm and 40 mm, respectively. Diameter Dv of the turbulent orifice is 2 mm, the discharge coefficient Cd is 0.6 and oil density is 860kg/m^3. The mass on the piston rod is m = 5000 kg. Transmission line losses and compressibility are neglected.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating at a speed of 1800 rpm. if the speed held constant and the impeller diameter is change to 203.2 mm, what is the new dischange og the pump in liters per second
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
A well has ¾ in of sucker rod and 21/2 in tubing with a specific gravity of the produced fluid of 0.7. The pump speed is 15rpm and the plunger is 2in diameter with polished rod string length of 64in. Assuming a well pump is set at 3100ft, calculate the power required for the prime mover if the surface tubing pressure is 100psia and the fluid level in annulus is 200ft above the pump. (Take the weight of sucker rod = 5868lbm and Sp = 52.5).
4. A centrifugal pump delivers water to a height of 22 metres at a speed of 800 r.p.m. The velocity of flow is constant at a speed of 2-0 m/s and the outlet vane anglc is 45°. If the pump discharges 225 litres of water per second, find the diameter of the impeller and width of the impcller at oudet. (Ans. 375 mm: 95 mm)
her of partic Fluid Flow /Liquid of density 1200 kg/m² throgh a pipe of 50mm inte intemal dimeter an orifice, lo mm in dimeter is fitted in the life and differential Pressure Shwn on amercury manometer is 0-1 m. assuming the leads the manometer are filled with the flowing fluid, calculate @ the mass flow fate of fluid flowing the approximate drop in pressure. caused by the orifice in KN/m² pe of 50 mm in d differential the flowing flu ifice in kN/m the density bartle wers c the coefficient of discharge ugybe taken as 0-61 and the density of mercury is 13,550 kg/m³
A piezometer and a Pitot tube are tapped into a horizontal water pipe, as shown in the Figure I belowto measure static and stagnation (static + dynamic) pressures. For the indicated water column heights,determine the velocity at the center of the pipe. Clearly state all asuumptions and illustrations
The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity of air flowing if density is 1.16kg/m3.
Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h1 = 0.3 m, compute the water flow from side nozzle of diameter (d = 10 mm) and the rise h₂ from that nozzle. vesn Air pressure It, 11₂ Nozzle
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 3.1 Find the maximum allowable speed to operate the pump 3.2 What power is expected in overcoming friction at this speed, takef = 0.01
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
If Hb is the presssure head corresponding to absolute pressure on the surface of the fluid, Z is the height of the fluid surface above or below the pump centerline, hf is the total friction head loss and Hv is the pressure head corresponding to the vapor pressure of the liquid. What is the available NPSH of the pump?