Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o, = 12 ksi, determine the principal stresses acting at the point. 15 ksi 4 ksi O 21.00 ksi and -13.00 ksi O 28.47 ksi and -17.91 ksi O 22.23 ksi and -13.85 ksi O 15.56 ksi and -16.69 ksi O 17.51 ksi and -10.50 ksi

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o, = 12 ksi, determine the principal stresses acting at the point. 15 ksi 4 ksi O 21.00 ksi and -13.00 ksi O 28.47 ksi and -17.91 ksi O 22.23 ksi and -13.85 ksi O 15.56 ksi and -16.69 ksi O 17.51 ksi and -10.50 ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stresses shown below act on horizontal and vertical planes through a point on the surface of a stressed body. Determine and show on a sketch the principal stresses and the maximum shear stress at this point. 30 ksi 5 ksi -20 ksi
Draw For the state of plane stress shown below, determine the principal stresses, the maximum in- plane shear stress and the average normal stress; and show the stresses on properly oriented elements. 413 ks - 1.8 ksi 灣彩

4. The state of plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30° clockwise with respect to the original element. 50 MPa 80 MPa 80 MPa 25 MPa * 50 MPa
Q1/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa 100 kPa tal stress enks 400 kPa
The state of plane stress at a point with respect to the xy-axes is shown in Fig. (a). Using Mohr's circle, determine (1) the principal stresses and principal planes; (2) the maximum in-plane shear stress; and (3) the equivalent state of stress with respect to the x'y'-axes. Show all results on sketches of properly oriented elements. y20 MPa 50° 40 MPa 16 MPa (a)
Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 Ib 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please I =
At a point in a stressed body the state of stress on two planes 45° apart is as shown below Determine the two principal stresses in MPa. 3 MPa 8 MPa 45° 3 MPa 2 MPa (a) 8.242, 0.658 (b) 9.242,0.758 (d) 8.242,0.758 (c) 9.242, 0.758
Q1/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa pisres shear Stress at 100 kPa al stress aximum plar arenis ec 400 kPa
Q1: For the Figure shown below, determine (a) the principal stresses and show them on a sketch of a properly oriented element, and (b) the maximum in-plane shear stresses and show them on a sketch of a properly oriented element. 60 MPa 45 MPa 30 МРа
The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. 1. Calculate the normal stress at the x-axis a. 69.8 MPa b. 75.25 MPa c. -39.8 MPa d. -24.60 MPa 2. Calculate the normal stress at the y-axis a. -39.8MPa b. 69.8 MPa c. -24.60 MPa d. 75.60 MPa 3. Calculate the shearing stress at the xy-face a. 55 MPa b. -55 MPa c. 65 MPa d. -65 MPa
Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a diameter of 0.8 in. Take P = 2000 lb. 2.5 in. 600 lb max The principal stresses are: ksi 1 in. Determine the principal stresses and the maximum shearing stress at point H. (Round the final answers to two decimal places. Input the answers with the appropriate sign.) A 3.5 in Omin ksi The maximum shearing stress is ksi,
Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle to determine (1) the principal stresses, (2) the principal stress direction, (3) the maximum in-plane shear stress and corresponding and normal stress. 100 MPa 150 MPa Tay - 50 MPa