Consider the flow of oil with p= 894 kg/m³ and µ = 2.33 kg/m.sin a 40 cm diameter pipeline at an average velocity of 0.5 m/s. A300 m long section of the pipeline passes through the icy watersof a lake. Disregarding the entrance effects, determine thepumping power required to overcome the pressure losses and tomaintain the flow of oil in the pipe.

Answered: Image /qna-images/answer/b23ec253-2a56-4a71-b4a4-ded02ba904d2.jpg

Answered: Consider the flow of oil with p = 894…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rate of flow of water through a cylindrical tube that has an inner radius of 1.2 cm is 2791 cm3 in 88s at 293 K. Determine if the flow laminar or turbulent.
A liquid flows through a 200 m long pipe with a rectangular cross section with 0.6mX0.3mdimensions. The dynamic viscosity of the liquid is 2.33 kg/ms and the density is 894 kg/m3. Ifthe average velocity of the fluid is 0.8m/s what is the necessary pumping power in kW tomaintain the flow of the liquid?
Oil is to flow through a pipe at 80°C, and for experimental purposes, the oil flow must be hydrodynamically and thermally fully developed laminar flow. If the pipe diameter is set at 2.5 cm, what is the minimum pipe length needed to ensure the flow conditions are met and the required pumping power to overcome the pressure loss in the pipe?
It is observed that water at 20°C rises up to 20 m height in a tree due to capillary effect. The surface tension of water at 20°C is ?s = 0.073 N/m and the contact angle is 20°. The maximum diameter of the tube in which water rises is (a) 0.035 mm (b) 0.016 mm (c) 0.02 mm (d) 0.002 mm (e) 0.0014 mm
Oil with density 917 kg/m^3 and viscosity 2.33 kg/m.s flows in a 400 meter long 41-cm-diameter horizontal pipeline at an average velocity of 0.7 m/s. Determine the pumping power required in kW to overcome the pressure losses and to maintain the flow of oil in the pipe. Make sure to check Reynolds number first to identify the type of flow and use the proper equation
Heated air at 1 atm and 100F is to be transportedin a 400-ft-long circular plastic duct at a rate of 12 ft3/s. Ifthe head loss in the pipe is not to exceed 50 ft, determine theminimum diameter of the duct.
Q1 What is the Reynolds number? How is it defined for (a) flow in a circular pipe and (b) flow over a flat plate. Consider a person walking first in air and then in water at same speed. For which motion will the Reynolds number be higher? Explain.
Consider the flow of oil with ? = 894 kg/m3 and ? = 2.33 kg/m·s in a 28-cmdiameter pipeline at an average velocity of 0.5 m/s. A 330-m-long section of the pipeline passes through the icy waters of a lake. Disregarding the entrance effects, determine the pumping power required to overcome the pressure losses and to maintain the flow of oil in the pipe.
Air flow through the pipe at a rate of 170 L/s. The pipe diameter ismeasured to be 20 cm at the entrance, which reduces to half with asmooth reducing section. The pressure difference between the two pipesections is measured by a water manometer. Assume the systemoperates in the environment at a constant temperature 50°C. Determine the differential height of the water in the manometer and list 3 assumptions that you made.
Water at 10 C flows in a 3.5-cm-diameter pipe at a velocity of 1.75 m/s. The Reynolds number for this flow is ?
An electronic device is cooled by water flowing through capillary holes drilled in the casing as shown in below figure. The temperature of the device casing is constant at 353 K. The capillary holes are 0.3 m long and 2.54x10-3 m in diameter. If water enters at a temperature of 333 K and flows at a velocity of 0.2 m/s, calculate the outlet temperature of the water. 0.3 m 0000000000 Surface Water 333 K 0.2 m/s 2.54 x 10m temperature = 353 K Water Capillary holes Single capillary
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe lengthis 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should bethe different in elevation between the upper and lower levels in order to achieve this pressure? Takethe density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS