Consider the magnetic core shown in the figure. The depth of the core into the page is 5 cm. The coil has 2000 turns and 2 A current. The relative permeability of the core is 3000. Determine the flux density in the right, center, and left sections of the core. T 10cm 1 .cm 2000 turns 20cm cm 12 -20cm -20cm 10cm 10cm 10cm 10cm

Consider the magnetic core shown in the figure. The depth of the core into the page is 5 cm. The coil has 2000 turns and 2 A current. The relative permeability of the core is 3000. Determine the flux density in the right, center, and left sections of the core. T 10cm 1 .cm 2000 turns 20cm cm 12 -20cm -20cm 10cm 10cm 10cm 10cm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A ferromagnetic core is shown in Figure Pl-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 800. 1-5. 10 cm- 5em 20 em 15 cm 15 cm 15 cm Coe depth - Scm SOLUTION There are three regions in this core. The top and bottom form one region, the left side forms a second region, and the right side forms a third region. If we assume that the mean path length of the flux is in the center of each leg of the core, and if we ignore spreading at the corners of the core, then the path lengths are I, = 2(27.5 cm) = 55 cm, I, = 30 cm, and /, = 30 cm. The reluctances of these regions are:
A ferromagnetic core is shown below. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.003 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. 1. - 10 cm--- - 20 cm - 15 cm 500 tums 15 cm 15 cm [1.21 A, 0.4 T, 1.2 T]
A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800
A magnetic circuit has a length of 100 cm and cross-sectional area of 5 square cm. The total flux is 10 x 10 webers. The coil has 100 turns and current of 4 amperes. What is the magnetic strength? a. 500 AT/m b. 400 AT/m c. 350 AT/m d. 450 AT/m
An air core toroidal coil has 120 turns, the length is 12 cm and 12 sq. cm in area What is the current required to set up a flux of 1.2x10° weber. What is the current?
A magnetic ring has reluctance of 1.675 × 10⁰ AT weber. The flux to be produced by the coil is 800 x 10 webers, then the AT required for the m.m.f. will be
1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of legs with 2 different cross-sectional areas.The depth of core is 10cm.The relative permeability of the core is 2000. The current in the magnetising coil is 1 A. The number of turns of the coil is 2000.Calculate: (i)the reluctances and draw the magnetic circuit (ii)the flux in the core (iii)Flux densities B and field intensities H in legs having different cross-sectional areas. (iv)Verify Ampere's Law. Depth: 10 cm I=1A 20cm 2000 Turns 65cm 15cm 15cm 50cm 15cm ndo un of
Question: 01 A two-legged core is shown in figure below. The winding on the left leg of the core (N) has 800 turns. The depth of the core is 15 cm. The small airgap is 0.05 cm and there is no fringing effect. If the dimensions are as shown, then determine the total reluctance of the given core when u, =800 and constant. 15cm 25cm 10cm 10cm 50cm N=800 5cm
A magnetic circuit with a cross-sectional area of 20 cm? is to be operated at 50 Hz from a 120 V rms supply. The number of turns required to achieve a peak magnetic flux density of 1.8 T in the core is
Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
A ferromagnetic core in the shape of a doughnut has a cross-sectional area of 0.11 m2 and an average length of 1.4 m. The permeabil ity of the core is 1.206 × 10-3 Wb/A-t. m. Determine the reluctance of the magnetic circuit
5. A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800 а. 1.0 А c. 1.5 A b. 2.0 A d. 2.5 A