Consider the pipe system shown in the figure. Oil (μ = 0.3 Pa-s) flows at a rate of 20 L/s through 100-mm diameter cast-iron pipe (ε = 0.26 mm). The fluid enters the pipe through an entrance (r/d = 0.1) and exits after passing through a wide-open angle valve. What is the total minor loss in the pipe? a.2.61 m b.0.72 m c.1.69 m d.1.17 m OIL SG = 0.90 Z Angle valve 2.6 m Consider flow of water (μ = 0.001 Pa-s) in the 6-cm diameter cast-iron (ε = 0.26 mm) pipe shown in the figure. What is the discharge in the pipe? a.70.2 lps d = 6 cm b.10.9 lps c.40.5 lps d.100.2 lps -10 m P₂ = 250,000 Pa P₁ = 350,000 Pa Consider the EGL and HGL of the 200-m pipeline shown. There is a turbine at CD and the fluid is water. Neglect minor losses. What is the velocity in pipe BC? 258.482 m a.29.72 m/s EGL 235.138 m 252.646 m b.5.84 m/s c.10.70 m/s 160.085 m d.45.03 m/s A HGL L = 100 m 229.302 m 190.106 m B 115.053 m 75.053 m f= 0.01 40° 120.085 m CD f = 0.01 45.032 m 0 m E

Consider the pipe system shown in the figure. Oil (μ = 0.3 Pa-s) flows at a rate of 20 L/s through 100-mm diameter cast-iron pipe (ε = 0.26 mm). The fluid enters the pipe through an entrance (r/d = 0.1) and exits after passing through a wide-open angle valve. What is the total minor loss in the pipe? a.2.61 m b.0.72 m c.1.69 m d.1.17 m OIL SG = 0.90 Z Angle valve 2.6 m Consider flow of water (μ = 0.001 Pa-s) in the 6-cm diameter cast-iron (ε = 0.26 mm) pipe shown in the figure. What is the discharge in the pipe? a.70.2 lps d = 6 cm b.10.9 lps c.40.5 lps d.100.2 lps -10 m P₂ = 250,000 Pa P₁ = 350,000 Pa Consider the EGL and HGL of the 200-m pipeline shown. There is a turbine at CD and the fluid is water. Neglect minor losses. What is the velocity in pipe BC? 258.482 m a.29.72 m/s EGL 235.138 m 252.646 m b.5.84 m/s c.10.70 m/s 160.085 m d.45.03 m/s A HGL L = 100 m 229.302 m 190.106 m B 115.053 m 75.053 m f= 0.01 40° 120.085 m CD f = 0.01 45.032 m 0 m E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3 As shown in the figure below, water (kinematic viscosity of water v =10m's) flows out of a reservoir (minor loss coefficient at A, KL = 0.7) into a system of two pipes discharging into another reservoir. The first pipe, which goes from A to B has a diameter D=0.12m and is 12 m long. The V %3D second pipe, which goes from B to C has a diameter D2=0.32m and is 13m long. The Darcy-Weisbach friction factor is the same for each pipe and is approximately equal to Hi 2=0.017. The water level Pn into the upstream reservoir is H,=10 m and the volumetric flow rate in the Datum z=0 system is Q=0.02 m³/s. 3.1) Sketch the Hydraulic Grade Line (HGL) and the Energy Grade Line (EGL) considering all losses (abrupt expansion K, = (1- ) %3D Compute the gauge pressure Pn read by the Bourdon manometer right downstream of the sudden expansion (assume the centre of gravity of the manometer is located at z=2.5m). 3.2)
4. If the pressure difference between points 1 and 2 below is 90 psi, what will be the flow rate? The pipes are galvanized iron with ks = 0.0005 ft. Take kinematic viscosity equal to 1.06 x 10-5 ft²/s and neglect minor losses. 10 in dia 1. 2000 ft, 8 in dia A B 1600 ft, 6 in dia C 800 ft, 10 in dia 2.
Problem 3: A turbulent flow in a pipe has a Reynolds number of 200,000. The pipe diameter is 125 mm, andthe surface has the roughness of coarse concrete (use value in table on Moody diagram above for roughnessheight). Find the following:a. The Relative Pipe Roughness (?⁄?): ___________________________________b. Friction factor read from Moody Diagram: ______________________________c. Friction factor calculated with an appropriate formula: ____________________
Find the diameter of a pipe of length 6 km when rate of flow of water through the pipe is 250 litre/sec and head loss due to friction is 6 m. Take C = 55 for Chezy's formula. %3D
Explain the major and minor losses? Then solve for the parallel pipes system shown below, a pump is placed in line 2 so that 0.142 m³/s will flow through each pipe. Pipe material is cast iron and for each elbow. Find the relation between the head loses hL1 and h12 and estimate the necessary pump head. Water viscosity is μ=1x10-³ Pa.s. Line 1, L-30 m, D= 6 inches Q₁-0.142 m³/s Pump Line 2, L, 30 m, D-3 inches Q-0.142 m/s R
4. In a vertical pipe carrying water, pressure gauges are inserted at points A and B where the pipe diameters are 0.2 and 0.08 m respectively. The point B is 3 m below A, and when the flow rate down the pipe is 0.02 m/s, the pressure at B is 15 kPa greater than at A. Assume that the losses in the pipe between A and B can be expressed as: dA -0.2m de - 0.08 m Rp k- 2g where v is the velocity at A. a) Find the value of k. b) If the gauges at A and B are replaced with tubes filled with water and connected to a u- tube containing mercury of relative density 13.6, what is Rp?
1) A smooth steel pipe of diameter 500 mm and length 850 m carry water at the rate of 0.05 m3/sec. Find the head lost due to friction. Take Kinematic Viscosity of water as 0.018 x 10 m2/sec 2)Determine the friction factor, “f” if Ethyl Alcohol at 25 C is flowing at 5.3 m/sec in a standard DN 40 Schedule 80 steel pipe 3)Determine the energy loss that will occur as 100 Liters / min of water flows from a small copper tube to a larger tube through a gradual enlargement having an included angle of 30 degrees. The small tube has a 25 mm OD x 1.5 wall thickness; the large tube has an 80 mm OD x 2.8 mm wall thickness.
3:'A hydraulic oil is flowing in a horizontal drawn steel hydraulic tube ( ɛ = 1.5 x 10-6m) with an ID of 0.047m. A pressure difference of 68 kPa is || observed between two points in the tube 30 meters apart. The oil has a specific gravity of 0.90 and a dynamic viscosity of 3.0 × 10¬³P ·s. Calculate the velocity of the flow of oil using Method Il-C iteration.
Ex. 2.11 A pump delivering 230 Ips of water whose absolute viscosity is 0.0114 Poise has a 300-mm diameter suction pipe and a 254-mm diameter discharge pipe as shown in the figure below. The suction pipe is 3.5 m long and the discharge pipe is 23 m long. The water is delivered 16 m above the intake water level. Considering the head losses in fittings and valves, find the head which the pump must supply. If the motor brake power of the driving motor is 75 kW, what is the efficiency of the pump? Assume the pipe material as cast iron. Given: A figure showing a pumping installation Q= 230 Ips D = 300 mm D = 254 mm H = 0.0114 Poise = 0.00114 Pa-s BP = 75 kW %3D %3D Standard elbow Standard elbow Discharge reservoir Long sweep elbow z=z, +2, Pump Source Foot valve & strainer Required: a) The total dynamic head b) The pump efficiency wilz,
Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe has an internal diameter of 250 mm and a total length of 1600 m. The pipe flow is fully-developed. The shear viscosity of the water is 1 mPa.s. g) Calculate the power required to pump the water if the fluid flow is laminar. Provide your answer to two decimal places.
A paint shop in the water flow through the pipe in the radius r Q = 0.05 m /s, density p= 1000 kg/m 3 type. The pipe friction coefficient is Cf= 0.0075 and the local loss coefficient K = 10. Pressure drop in the pipe; AP = p 2C K %3D where the water velocity in the pipe can be calculated with V = Q/(r²). What should be the radius of the pipe so that the pressure drop that will occur in a pipe of L = 100 m length does not exceed AP = 200 000 N/ m 2? State the tolerance value provided by the result you found.
Heavy fuel oil flows from A and B through a 1000 m horizontal 150mm diameter steel pipe. The pressure at A is 1050 kPa and at B is 35 kPa. The kinematic viscosity is 0.000413 m²/s and the specific gravity is 0.92. What is the flow rate?A. 0.0332 m³/sB. 0.1445 m³/sC. 0.8582 m³/sD. 1.2244 m³/s